Instrukcja obsługi Behringer Oscillator Module 1004
Behringer
syntezator
Oscillator Module 1004
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Behringer Oscillator Module 1004 (2 stron) w kategorii syntezator. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
Quick Start Guide
OSCILLATOR MODULE 1004
Legendary 2500 Series Dual Core VCO
Module for Eurorack
Controls
(1) COARSE FREQUENCY – Sets the frequency from 0.03 to
32 Hz in the low (LFO) range, or from 15.5 Hz to 16 kHz in
the high (audio) range, depending on the Fine frequency
knob setting.
(2) FINE FREQUENCY – Adjusts the frequency by a factor of
±1 octave, potentially halving or doubling the frequency
at either extreme.
(3) ENABLE switch – Turns the oscillator on and o.
(4) RANGE switch – Determines whether the oscillator
operates in the low (subsonic/LFO) band or the high
(audio) band.
(5) WAVEFORM switches – Engage up to 5 waveforms by
moving the relevant toggle switch to the left, or engage
the inverse waveform by moving the switch to the right.
The center position turns the waveform o. Engaging
multiple switches simultaneously produces the average of
all active waveforms.
(6) PW knob – Manually control the pulse width for the
pulse waveform.
(7) FM 2 knob – Attenuates the signal connected to the FM
2 input.
(8) PWM knob – Adjusts the modulation depth of the PMW
control input.
(9) FM 1 knob – Attenuates the signal connected to the FM
1 input.
(10) KYBD – Connect a keyboard or other external frequency
control via 3.5 mm TS cable.
(11) FM 1/2 – Connect external voltages to modulate
the frequency.
(12) PWM – Connect an external voltage to modulate the
pulse width.
(13) OUT – Send the oscillator signal to other modules via
3.5 mm TS cable.
Power Connection
The unit comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector
a tab that will align with the gap in the socket, so it cann
be inserted incorrectly. If the power supply does not hav
a keyed socket, be sure to orient pin 1 (-12 V) with the re
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back
the module. The connector has a tab that will align with
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn
the power supply.
(1)
(2)
(3)
(6)
(7)
(8)
(5)
(4)
(9)
( ) ( ) ( ) ( )10 11 12 13
V 1.0
Specyfikacje produktu
| Marka: | Behringer |
| Kategoria: | syntezator |
| Model: | Oscillator Module 1004 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Behringer Oscillator Module 1004, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje syntezator Behringer
3 Stycznia 2025
3 Stycznia 2025
3 Stycznia 2025
3 Stycznia 2025
31 Grudnia 2025
14 Grudnia 2024
9 Października 2024
7 Października 2024
7 Października 2024
5 Października 2024
Instrukcje syntezator
- LennarDigital
- Noise Engineering
- Yamaha
- ELTA Music
- X Audio Systems
- Elektron
- Pittsburgh Modular
- Korg
- IK Multimedia
- GS Music
- Native
- Erica Synths
- Moog
- Cre8audio
- Boss
Najnowsze instrukcje dla syntezator
19 Marca 2025
19 Marca 2025
19 Marca 2025
19 Marca 2025
19 Marca 2025
19 Marca 2025
19 Marca 2025
19 Marca 2025
19 Marca 2025
19 Marca 2025