Instrukcja obsługi Blaupunkt EMA 260

Blaupunkt system hi-fi EMA 260

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Blaupunkt EMA 260 (4 stron) w kategorii system hi-fi. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 7.5 użytkowników na średnio 4.8 gwiazdek

Pobierz PDF

Strona 1/4

System Planning

Proper system planning is the best way to maximize your amplifier performance.

By planning your installation carefully you can avoid situations where the perfor-

mance of the reliability of your system is compromised. Your authorized dealer

has been trained to maximize your system’s sonic potential. Your dealer is a

valuable resource in helping you with your system design and installation.

Speaker Requirements

Each channel of your amplifier can easily

drive 4Ωspeaker loads when used ion the

stereo mode. When a channel-pair is bridged,

the recommended minimum load impedance

is 3Ω for subwoofer use, and 4Ω for full range

operation. Although operation with lower

impedances is not likely to cause immediate

damage to the internal circuitry, the unit will

most likely overheat, causing the thermal

protection circuitry to shut down the amplifier.

When the chassis cools down, normal

operation will resume. Continuing to operate

the amplifier under these conditions is not

recommended and will reduce its life

expectancy.

Most speakers designed for car audio

operation are 4Ω impedance. Connecting

two such speakers in parallel will result in

a 2Ω nominal impedance, which is not

recommended for use with bridged

channels of your amplifier.

Symptom

Distorted output

(cont’d)

Poor bass response

Battery fuse blowing

Amplifier fuse blowing

Possible Cause

Speakers are blown

Speakers wired wrong

polarity causing cancellation

at low frequencies

Crossover set incorrectly

Impedance load to amplifier

too low

Short in power wire or

incorrect power connections

Fuse used is smaller than

recommended

Too much current being drawn

Short in power wire or

incorrect

Too much current being drawn

Fuse used is smaller than

recommended

Action to take

Check system with known

working speaker and repair

or replace as needed

Check speaker polarity and

repair as needed

Reset crossover referring to

the multi-cross crossover

configuration section of this

manual for detailed instructions

Check speaker impedance load,

if below 2Ω stereo or 4Ω mono

rewire speakers to achieve a

higher impedance

Check power and ground

connections and repair as

needed

Replace with proper fuse size

Check speaker impedance load,

it below 2Ω stereo or 4Ω mono

rewire speaker to achieve a

higher impedance and replace

with recommended fuse size

Check power and ground

connections and repair as

needed

Check speaker impedance load.

It below 2Ω stereo or 4Ω mono

rewire speakers to achieve a

higher impedance and replace

with recommended fuse size

Check power and ground

connections and repair as

needed

Replace with proper fuse size

PRT

PWR

OUTPUT

INPUT

32Hz 250Hz

HPF

32Hz 250Hz

LPF GAIN

MAXMIN

BASS

BOOST

6dB

TREBLE

BOOST

6dB

CROSS

OVER

HPF

FULL

LPF

BRIDGE

FUSEGND REM +12V

POWER INPUT

L R

SPEAKER OUTPUT

Power Connection Leads

Notes on the power supply

Connect the +12V power input lead only after all other leads have been connected.

Be sure to connect the ground wire of the unit securely to a metal part of the car. A lose

connection may cause a malfunction of the amplifier.

REMOTE: The unit is turned on by applying +12Volts to this terminal. This terminal

does not draw heavy current like the two power terminal so a thinner connecting wire is

acceptable. Standard 18 GUAGE is fine and the standard color is yellow. If the power

antenna wire is already in use, you can still splice into it. With this method, the unit will

turn on automatically with the radio. Use the power supply lead with a fuse attached

whose value is the same as original fuse.

Place the fuse in the power supply lead as close as possible to the car battery.

During a full power operation. Maximum current will run through the system. Therefore,

Make sure that the leads to be connected to the +12V and GND terminals of the unit

respectively must be larger than 10-Guage (AWG 10)

Symptom

No output

Audio cycles on and off

Distorted output

Possible Cause

Low or no remote turn-on

input

Fuse down

Power wires not connected

Audio input not connected or

no output from source

Speaker wires not connected

Speaker are blown

Thermal protection engages

when amplifier heatsink

temperature exceeds 90

Loose or poor audio input

Amplifier level sensitivity set

too high; exceeding maximum

output capability of amplifier

Impedance load to amplifier

too low

Shorted speaker wires

Speaker not connected to

amplifier properly

Action to Take

Check remote turn-on voltage

output at amplifier and correct

as needed

Check power wire integrity

and reversed polarity, repair a

s needed and replace fuse

Check power wire and ground

connections and repair of

replace as needed

Check input connections and

signal integrity, repair or

replace as needed

Check speaker wires and repair o

r replace as needed

Check system with known

working speaker and repair or

replace speakers as needed

Make sure there is proper

ventilation for amplifier and

improve ventilation as needed

Check input connections and

repair or replace as needed

Reset gain referring to the

turning section of the manual

for detailed instructions

Check speaker impedance load

if below 2 stereo or 4 mono Ω Ω

rewire speakers to achieve a

higher impedance

Check speaker wire

connections and repair or

replace as needed

Check speaker wiring and

repair or replace as needed

refer to the installation section

of this manual for detailed

instructions

Trouble Shooting

Specyfikacje produktu

Marka:	Blaupunkt
Kategoria:	system hi-fi
Model:	EMA 260
Kolor produktu:	Czarny
Impedancja:	4 Ω
Kanały wyjścia audio:	2.0 kan.
Wymiary produktu (SxGxW):	56 x 230 x 200 mm
Zasięg częstotliwości:	20 - 25000 Hz
Maksymalny poziom na wejściu:	8 V