Instrukcja obsługi Blaupunkt SR-S1

Blaupunkt system alarmowy SR-S1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Blaupunkt SR-S1 (2 stron) w kategorii system alarmowy. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2.5 użytkowników na średnio 3.7 gwiazdek

Pobierz PDF

Strona 1/2

Wireless Indoor Siren (SR S1)-

1. Mounting Holes x 4

2. Tamper Switch

The tamper switch protects the from being opened.cover

3. Function Switch Block

Contains 7 to enable the learning mode and to set DIP Switches

the alarm period of siren.

1 x Indoor Siren

4 x large wall plugs and screws

4 V x 1.5 D alkaline batteries

1. Open the front cover

2. Open the battery cover to insert batteries.compartment

3. ocate the L Function Switch Block. Use a sharp bject to o set

Dip SW3 & SW4 on the function switch block to your desired

alarm length.

4. ontrol anel Enter learning mode for your c p .

5. Slide the position Dip SW1 to ON . SR S1- will enter learning

mode. he code After 3 seconds, t Siren will send a learning

and emit a beep to confirm.

6. If the Control Panel receives the learning signal, please refer

to the Control Panel manual to complete the learning process.

When learning is complete, the Control Panel will send signal

to the The Siren to confirm. Siren will sound a short beep

again to indicate learning is successful.

If the Control Panel fails to receive a learning code, slide Dip

SW1 back to OFF, and then ON position again to enter

learning mode again.

7. does no I f the Siren t respond, please remove the Siren from

the control panel and repeat steps 4-6 again.

8. S lide Dip the SW1 to OFF position to leave learning mode. If

you do t slide Dip SW1 back to OFF position, the no Siren will

automatically leave the learning mode in one hour.

The Indoor Siren has 4 mounting holes on the back cover for wall

mounting.

Before Installation, refer to your Control Panel manual to

temporarily disable the Siren Tamper function to avoid

accidental alarm trigger.

1. Use the 4 mounting holes on the back to mark position on the

wall.

2. Drill holes into the wall using the mounting holes as template,

insert wall plugs if required,

3. Fix the base onto the wall with the screw and plugs provided.

4. Replace the front cover onto the base.

5. Enab le the Siren Tamper function on you Control Panel.

SW1

Siren Learning

OFF

Normal operation

Learn-in mode

SW2

Reserved

SW3

SW4

Siren Duration

OFF

3 min.

OFF

5 min.

OFF

10 min.

1 second (test)

SW5

Reserved

SW6

Memory Reset

OFF

Normal

Clear Memory

SW7

Supervision

OFF

Supervision function disable

Supervision function enable

 For further detail please see

aanndd

Mounting Holes

x 4

Specyfikacje produktu

Marka:	Blaupunkt
Kategoria:	system alarmowy
Model:	SR-S1
Kolor produktu:	Biały
Poziom ciśnienia akustycznego:	104 dB
Technologia baterii:	Alkaliczny
Zakres temperatur (eksploatacja):	-10 - 45 °C
Rodzaj baterii:	AAA
Diody LED:	Status
Model:	Syrena bezprzewodowa
Liczba baterii:	4
Wymiary produktu (SxGxW):	113 x 54 x 228 mm
Czas eksploatacji baterii:	2.5 lat(a)
Częstotliwość (MHz):	868 MHz
Napięcie baterii:	1.5 V
Liczba dźwięków alarmowych:	3