Instrukcja obsługi Chord SPM 6000 Mk2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chord SPM 6000 Mk2 (5 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 19 osób i została oceniona przez 10 użytkowników na średnio 4.3 gwiazdek
Strona 1/5
SPM 6000 MK2
POWER AMPLIFIER MANUAL
OPERATING INSTRUCTIONS
INSTALLATION
Your amplifier should be positioned to ensure a free flow of air over the rear heat sink and through the upper and
lower grilles. When driven continuously at well above average listening levels, the temperature on the heat sink may
exceed 50oC. This is not a fault, but an indication of the need for adequate ventilation.
Please ensure that the IEC mains lead is correctly terminated.
UK/EUROPE Brown = LIVE = Black USA/CANADA!
Blue = NEUTRAL = White!
Yellow/Green = EARTH = Green
THE SPM 6000 Mk 2 MUST BE EARTHED AT ALL TIMES VIA ITS OWN MAINS LEAD.
FAILURE TO DO THIS MAY BE HAZARDOUS.
CE This unit complies with EN 50081-1 & IEC 801/2
It has come to light that, in some European
countries a hum may occur if Pre and Power
Amplifiers are connected to mains wall sockets
which do not have an earth. Please ensure
that, if this is the case, the pre and power amps
are connected via a multi-way mains block
which contains an earth point at each socket
outlet. This is to ensure that the chassis
metalwork of each item is connected together
and Chord Electronics Limited firmly
recommends that an earthing method for the
building is implemented.
REAR PANEL
The rear of the SPM 6000 Mk 2 has two sets of inputs, one set of balanced XLR connections and one set of phono
RCA connectors. You will also notice by looking at the diagram below that the inputs can be connected as either
INVERTING or NON-INVERTING modes. Connecting to either the phono or the XLR on the right hand side will
give an inverted output as is normal with other Chord amplification. However if a non-inverting output is preferred
simply connect to the left hand side. As the SPM 6000 Mk 2 is of mono block construction only one of the inputs
should be used. Where a pair of units is used for stereo operation the user should take care to connect both amplifiers
in the same manner so as not to have an out of phase configuration. The input should be connected last, with the
amplifier switched off.
There are two sets of high current gold plated output terminals, the speaker may be connected to either the left
or the right set of terminals. For Bi-wiring configuration both sets of outputs can be used.
!
Specyfikacje produktu
| Marka: | Chord |
| Kategoria: | odbiornik |
| Model: | SPM 6000 Mk2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Chord SPM 6000 Mk2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje odbiornik Chord
14 Października 2024
29 Września 2024
29 Września 2024
29 Września 2024
12 Września 2024
9 Września 2024
5 Września 2024
3 Września 2024
3 Września 2024
2 Września 2024
Instrukcje odbiornik
- odbiornik Cayin
- odbiornik RetroSound
- odbiornik GigaBlue
- odbiornik Audibax
- odbiornik Technics
- odbiornik Simaudio
- odbiornik Xsarius
- odbiornik JUNG
- odbiornik Cerwin-Vega
- odbiornik VigilLink
- odbiornik Crest Audio
- odbiornik Smartwares
- odbiornik Meliconi
- odbiornik Summit Audio
- odbiornik Monacor
Najnowsze instrukcje dla odbiornik
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
30 Marca 2025