Instrukcja obsługi Crestron DM-TX-4K-100-C-1G-B-T

Crestron przedłużacz AV DM-TX-4K-100-C-1G-B-T

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Crestron DM-TX-4K-100-C-1G-B-T (2 stron) w kategorii przedłużacz AV. Ta instrukcja była pomocna dla 32 osób i została oceniona przez 16.5 użytkowników na średnio 4.6 gwiazdek

Pobierz PDF

Strona 1/2

DO GUIDE

DO Install the Device

The DM-TX-4K-100-C-1G can be mounted into an electrical box, under a table, or onto a at

surface or rack rail.

Mounting into an Electrical Box

The DM-TX-4K-100-C-1G mounts into a 1-gang electrical box (not included). A minimum

mounting depth of 3-1/2 inches (89 mm) is required.

Using a Phillips head screwdriver, attach the DM-TX-4K-100-C-1G to the electrical box using

the two included 6-32 x 3/4-inch truss combo head screws. Then, attach a decorator-style

faceplate (not included) to the front panel of the DM-TX-4K-100-C-1G using two screws (not

included). Refer to illustration .

 Mounting into an Electrical Box

DM-TX-4K-100-C-1G

Wall Plate 4K DigitalMedia 8G+® Transmitter 100

DO Make Connections to the Rear Panel

Make connections to the rear panel of the Crestron® DM-TX-4K-100-C-1G before mounting the

unit into an electrical box. If the unit is to be mounted under a table or onto a at surface or rack

rail, make connections to the rear panel after the unit is mounted. (For mounting instructions,

refer to the “DO Install the Device” section in this guide.)

Make connections to the rear panel as follows:

DM OUT: Connect to the DM 8G+® input of a DigitalMedia™ switcher, DigitalMedia 8G+®

receiver, or other DigitalMedia device or to an HDBaseT® device.

NOTE: The DM OUT port is a PoDM (Power over DM) and HDBaseT® PoE (Power over Ethernet)

PD (Powered Device) port. To receive PoDM or HDBaseT PoE, the DM-TX-4K-100-C-1G requires

a connection to a DigitalMedia switcher or other equipment that has a PoDM or HDBaseT PoE

PSE (Power Sourcing Equipment) port. Any wiring that is connected to a PoDM or HDBaseT PoE

PSE port is for intrabuilding use only and should not be connected to a line that runs outside of

the building in which the PSE is located.

24VDC 0.75A: Connect to the included power pack using the included 2-pin interface

connector.

NOTE: Connection to the power pack is not required when PoDM or HDBaseT PoE is used to

power the device.

G: Connect to earth ground (building steel).

Refer to illustrations for sample rear panel connections.  and

 Connection to DigitalMedia Switcher Using PoDM

(External Power Pack Not Required)

DO Check the Box

QTY PRODUCT COLOR PART NUM.

1 Bracket (for Interface Module) Black 2016054

2 Connector, 2-Pin 2003574

1 Connector, 3-Pin 2003575

1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2045866

2 Screw, 6-32 x 3/4", Truss Head, Combo 2009211

2 Screw, 6-32 x 1/4", Pan Head, SEMS Black 2007218

DM-RMC-4K-100-C

Ground

DM -R M C -4 K -1 0 0 -C

DM R OOM C ONT ROL LER

DB T

ASE

HDMI OUT

GND

TXRX

RTS

CTS

COM

LAN

DM IN

RESET

SETUP

24 V

0.75A MAX

Power

pack

 Connection to DigitalMedia Receiver

(External Power Pack Required)

DM-MD8X8

Ground

Specyfikacje produktu

Marka:	Crestron
Kategoria:	przedłużacz AV
Model:	DM-TX-4K-100-C-1G-B-T
Kolor produktu:	Czarny
Częstotliwość wejściowa AC:	50 - 60 Hz
Napięcie wejściowe AC:	100-240 V
Wysokość produktu:	105 mm
Szerokość produktu:	44 mm
Głębokość produktu:	60 mm
Waga produktu:	179 g
Technologia łączności:	Przewodowa
Prąd:	0.75 A
Napięcie pracy:	24 V
Standardy komunikacyjne:	IEEE 802.3at
Zakres temperatur (eksploatacja):	0 - 40 °C
Zakres wilgotności względnej:	10 - 90 %
Diody LED:	Tak
Model:	Nadajnik AV
Maks. rozdzielczość:	4096 x 2160 px
HDCP:	Tak
Możliwości montowania w stelażu:	Tak
Materiały:	Metal
Maksymalny dystans transferu:	100 m
Obsługiwane rozdzielczości grafiki:	1920 x 1080 (HD 1080),2560 x 1600 (WQXGA),3840 x 2160,4096 x 2160
HDMI in:	1
Wyjścia RJ-45:	1
Bypass HDCP i EDID:	Tak