Instrukcja obsługi Crestron HDI-XSPA

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Crestron HDI-XSPA (2 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 6 użytkowników na średnio 4.9 gwiazdek

DOGUIDE

HD(I)-XSPA

4K Ultra High-Denition 7.1 Surround Sound AV Receiver

DO Install the Device

The HD(I)-XSPA can be mounted in a rack or stacked with

other equipment. Two “ears” are provided so that the unit

can be rack mounted. These ears must be installed prior

to mounting. The only tool required is a #1 or #2 Phillips

screwdriver.

WARNING: To prevent bodily injury when mounting or

servicing this unit in a rack, observe the following guidelines:

•When mounting this unit in a partially lled rack, load

the rack from the bottom to the top with the heaviest

component at the bottom of the rack.

•If the rack is provided with stabilizing devices, install the

stabilizers before mounting or servicing the unit in the

rack.

CAUTION: To prevent equipment damage, use only the rack

ears Crestron®provides for this device.

NOTE: If rack mounting is not required, remove the feet from

the bottom of the unit with a screwdriver.

DO Make Connections to the Device

Make the necessary connections to the device as called out

in the diagram to the right. Connect the power last.

CAUTION: Keep the device unplugged until all of the input,

network, and speaker wiring is complete.

CAUTION: Check the speaker wires for shorts and frayed

wiring around the SPEAKER OUTPUTS connectors.

NOTE: The DM and LAN ports are for intra-building use only

and should not be connected to lines that run outside of the

building in which the unit is located.

NOTE: If the DM port is connected to a DM® switch, the LAN

port should not be connected to the local area network.

Additionally, the DM switch

can be used to congure the

network settings. Refer to

the DigitalMedia™ Design

Guide (Doc. 4546) at

www.crestron.com/manuals

for details.

NOTE: Ensure the unit is

properly grounded by con-

necting the chassis ground

lug to an earth ground

(building steel).

One balanced/unbalanced audio input is provided, utilizing a 5-pin terminal block connector. Refer to the following diagrams for

connecting a source.

DO Congure the Device

While the HD(I)-XSPA can be used right out of the box, the device can be

further customized with Crestron Toolbox™ or the front panel controls.

For details on using Crestron Toolbox, refer to the Crestron Toolbox help

le. For details on using the front panel controls, refer to the HD-XSPA

supplemental guide (Doc. 7448) at www.crestron.com/manuals.

DO Check the Box

QTYPRODUCTPART NUM.

2Bracket, Rack Ear, 2U2034434

8Connector, 2-Pin2012361

1Connector, 4-Pin2003576

3Connector, 5-Pin2003577

1Connector, 8-Pin2003580

1Cable, USB 2.0, A - B, 6’ (1.83 m)2014966

Items for HD-XSPA

1Power Cord, 6' 7" (2 m)4512528

1Fuse, 10.0 A, Time Lag, 1.25" x 0.25", Ceramic Cartridge, 250 V2017577

Items for HDI-XSPA

1Varies by countryPower Cord

1Fuse, 5.0 A, Time Lag, 5 x 20 mm, Ceramic Cartridge, 250 V2017578

Wiring for Balanced Input

Right

Left

Shield

Wiring for Unbalanced Input

Right

Left

Jumpers

+

L R

+ -+ -G

+

+

L R

+ -+ -G

+

USB:

To HID-Compliant Keyboard or

Mouse

AUDIO IN (DIGITAL):

From Digital Audio SourcesAUDIO IN (ANALOG):

From Analog Audio Sources

PREAMP OUT:

To Audio

Amplier

Ground

SPEAKER OUTPUTS:

To SpeakersPOWER:

From Line Voltage

DM:

From DigitalMedia Source

HDMI® IN:

From HDMI

Sources HDMI OUT:

To

HDMI Device

COM:

To

RS-232 DeviceRELAY:

To Controllable Device

SENS:

From Sensors

LAN:

10BASE-T/100BASE-TX Ethernet to

LAN

IR:

To IR Controlled Devices

Specyfikacje produktu