Instrukcja obsługi DeWalt DWE43144N
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DeWalt DWE43144N (4 stron) w kategorii młynek. Ta instrukcja była pomocna dla 55 osób i została oceniona przez 28 użytkowników na średnio 4.7 gwiazdek
Strona 1/4
ENGLISH
Lanyard Attachment Point Installation
To be used with DWE4222N, DWE43066N,
DWE43114N, DWE43115N, DWE43144N, DWE46144N,
DWE46166N Grinders
WARNING: The lanyard attachment point 1 may
only be added to certain models and must be installed
by an authorized service center.
WARNING: For your own safety, read the grinder
instruction manual before using any accessory. Failure
to heed these warnings may result in personal injury
and serious damage to the vacuum and the accessory.
WARNING: Retain this document with the tool
instruction manual for futurereference.
Lanyard Attachment Point (Fig. B)
Safety Warnings Specific for Use At Height
• If the tool is dropped for any reason, the lanyard
attachment point 1 must be inspected and properly
serviced prior to re-use. The lanyard attachment point
is designed to stretch to absorb the shock of a drop. Any
permanent stretch to the device exposing the red marked
internal coils indicates it has been compromised and must
be serviced prior toreuse.
• Always keep the tool and accessories tethered when
working "at height". (Maximum lanyard length: 6.5 ft
[2m])
• Use only with lanyards appropriate for this tool type and
rated for at least 6 lbs (2.72 Kg).
• Crush, cut or entanglement hazard. Do not use near
moving parts, mechanisms or runningmachinery.
• Do not anchor the tool lanyard to anything on your body.
Anchor to a rigid structure that can withstand the forces
of a droppedtool.
• Make sure the lanyard is properly secure at each end prior
touse.
• Inspect tool and lanyard before each use for damage and
proper function (including fabric and stitching). Do not
use if damaged or not functioningproperly.
• Do not alter the lanyard attachment point or use in a
manner other than as instructed in thismanual.
• Only attach tool to a lanyard with a locking carabiner. Do
not attach by looping or knotting the lanyard. Do not use
rope orcord.
• Electrical shock hazard. Be sure power is off when working
in high voltage areas. Some lanyards areconductive.
• Dropped tools will swing on the lanyard, which could
cause injury or loss ofbalance.
• Do not carry the tool by lanyard attachment point or
thelanyard.
• Do not attach more than one tool to eachlanyard.
final page size: 8.5 x 5.5 inches
• Only use appropriate
D WALTe
brand lanyard attachment
point. attachmentpoints NEVER modify tools to create .
• Only transfer the tool between hands while properly
balanced in a stableorientation.
• Do not attach lanyards to tool in a way that keeps guards,
switches or lock-offs from operatingproperly.
• Avoid getting tangled in thelanyard.
• Keep lanyard away from the cutting area of thetool.
• Do not use lanyards or attachment devices to get
additional leverage from thetool.
• Do not use for personal fallprotection.
• Falling object hazard! Only change accessories and
attachments where a dropped object won't cause
a hazard below you. Consult your Authority Having
Jurisdication (AHJ) or site supervisor for procedures for
working atheight.
• Use multi-action and screw gate type carabiners. Do not
use single action spring clipcarabiners.
The lanyard attachment point 1 is intended for use by
competent personnel, who are trained and knowledgeable
regarding working with tools in and around machinery and
"at height".
Installation
DWE43115N, DWE43066N, DWE46166N (Fig. A, B)
1. Position the loops of the lanyard attachment point on
each side of the tool housing.
2. Slide provided bolt through first washer, both loops and
the housing. Install second washer and nut onto bolt
and tighten securely.
IMPORTANT: Always use manual, torque-calibrated
screwdrivers and tighten to
15.9–18.6inlbs (1.8–2.1Nm). Do not use pneumatic or
electric screwdrivers.
DWE4222N, DWE43114N, DWE43144N, DWE46144N
(Fig. C, D)
1. Slide the metal bars of the lanyard attachment point
1 into the slots at the rear of the tool housing, making
note which has the threads.
2. Insert the screw into the housing side without the
threaded bar and feed it through until it engages the
threads of the other bar. Tighten the screw securely.
IMPORTANT: Always use manual, torque-calibrated
screwdrivers and tighten to 15.9–18.6inlbs (1.8–
2.1Nm). Do not use pneumatic or electric screwdrivers.
For more information, please contact
D WALTe
at the
address below or 1-800-4-
D WALTe
(1-800-433-9258).
FRANCAIS
Installation du point de fixation des
longes
À utiliser avec les meuleuses DWE4222N,
DWE43066N, DWE43114N, DWE43115N, DWE43144N,
DWE46144N, DWE46166N
AVERTISSEMENT: le point de fixation des longes
de sécurité 1 peut seulement être ajouté à certains
modèles et doit être installé par un centre de services
autorisé.
Specyfikacje produktu
| Marka: | DeWalt |
| Kategoria: | młynek |
| Model: | DWE43144N |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z DeWalt DWE43144N, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje młynek DeWalt
22 Sierpnia 2024
22 Sierpnia 2024
22 Sierpnia 2024
22 Sierpnia 2024
28 Lipca 2024
28 Lipca 2024
27 Lipca 2024
17 Czerwca 2024
17 Czerwca 2024
25 Maja 2024
Instrukcje młynek
- ABB
- Ferm
- Yato
- RYOBI
- Rodcraft
- Hitachi
- Black & Decker
- Nuova Simonelli
- Makita
- Kress
- Bavaria By Einhell
- Mesko
- DEDRA
- Cocraft
- Ozito
Najnowsze instrukcje dla młynek
27 Października 2024
22 Października 2024
1 Października 2024
1 Października 2024
28 Września 2024
21 Września 2024
21 Września 2024
17 Września 2024
4 Września 2024
2 Września 2024