Instrukcja obsługi DeWalt GR870
DeWalt
Maszyna do piłowania
GR870
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DeWalt GR870 (40 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 3.5 użytkowników na średnio 5.0 gwiazdek
Strona 1/40
GR870
14" (355 mm) Heavy-Duty Chop Saw
Scie fendeuse de 355 mm (14 po) et de service intensif
Cortadora de metales de 355 mm (14")
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. LÉASE ESTE INSTRUCTIVOADVERTENCIA:
ANTES DE USAR EL PRODUCTO.
GRABBER®
1
English
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR
ANY GRABBER TOOL, CALL US TOLL FREE AT: 1-800-477-
TURN (1-800-477-8876)
Important Safety Instructions
WARNING! Read and understand all instructions.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
•KEEP GUARDS IN PLACE and in working order.
•REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of
checking to see that keys and adjusting wrenches are removed
from tool before turning it on.
•KEEP WORK AREA CLEAN. Cluttered areas and benches invite
injuries.
•DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power
tools in damp or wet locations, or expose them to rain. Keep work
area well lighted.
•KEEP CHILDREN AWAY. All visitors should be kept at a safe dis-
tance from work area.
•MAKE WORKSHOP KID PROOF with padlocks, master switches,
or by removing starter keys.
•DON’T FORCE TOOL. It will do the job better and safer at the rate
for which it was designed.
•USE RIGHT TOOL. Don’t force tool or attachment to do a job for
which it was not designed.
•USE PROPER EXTENSION CORD. Make sure your extension
cord is in good condition. When using and extension cord, be sure
to use one heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. The following table shows the
correct size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gage. The smaller
the gage number, the heavier the cord.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more American Wire Gage
Than Than
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
•WEAR PROPER APPAREL. Do not wear loose clothing, neckties,
rings, bracelets, or other jewelry which may get caught in moving
parts. Nonslip footwear is recommended. Wear protective hair cov-
ering to contain long hair. Air vents often cover moving parts and
should also be avoided.
•ALWAYS USE SAFETY GLASSES which meet the ANSI Z87.1
requirements.Also use face or dust mask if cutting operation is
dusty. Everyday eyeglasses only have impact resistant lenses,
they are not safety glasses.
•SECURE WORK. Use clamps or a vise to hold work. It’s safer than
using your hand and it frees both hands to operate tool.
•DON’T OVERREACH. Keep proper footing and balance at all
times.
•MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for
best and safest performance. Follow instructions for lubricating and
changing accessories.
•DISCONNECT TOOLS before servicing; when changing acces-
sories, such as blades, bits, cutters, and the like.
•REDUCE THE RISK OF UNINTENTIONAL STARTING. Make
sure switch is in off position before plugging in.
•USE RECOMMENDED ACCESSORIES. Consult the instruction
manual for recommended accessories. The use of improper acces-
sories may cause risk of injury to persons.
•NEVER STAND ON TOOL. Serious injury could occur if the tool is
tipped or if the cutting tool is unintentionally contacted.
Specyfikacje produktu
| Marka: | DeWalt |
| Kategoria: | Maszyna do piłowania |
| Model: | GR870 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z DeWalt GR870, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Maszyna do piłowania DeWalt
12 Lutego 2025
3 Stycznia 2025
3 Stycznia 2025
3 Stycznia 2025
9 Października 2024
7 Października 2024
7 Października 2024
2 Października 2024
30 Września 2024
30 Września 2024
Instrukcje Maszyna do piłowania
- Maszyna do piłowania Kress
- Maszyna do piłowania Workzone
- Maszyna do piłowania Porter-Cable
- Maszyna do piłowania Scheppach
- Maszyna do piłowania Meec Tools
- Maszyna do piłowania Jonsered
- Maszyna do piłowania Elu
- Maszyna do piłowania Black & Decker
- Maszyna do piłowania DURO PRO
- Maszyna do piłowania McKenzie
- Maszyna do piłowania Maktec
- Maszyna do piłowania PowerPlus
- Maszyna do piłowania Toledo
- Maszyna do piłowania Lionelo
- Maszyna do piłowania Lux Tools
Najnowsze instrukcje dla Maszyna do piłowania
3 Kwietnia 2025
3 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
29 Marca 2025