Instrukcja obsługi Draper 253219 projection screen 253219
Draper
Ekran projekcyjny
253219 projection screen 253219
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Draper 253219 projection screen 253219 (2 stron) w kategorii Ekran projekcyjny. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 3.5 użytkowników na średnio 4.8 gwiazdek
Strona 1/2
Assembly/Mounting Instructions
Onyx Permanently Tensioned Projection Screen by Draper
Caution
① Read instructions through completely before proceeding.
② Follow instructions carefully. Installation con trary to instructions
invalidates warranty.
③ Screen should be accessible for complete removal should fabric
become damaged or should other ser vice be required.
④ Screen should be installed level (using a carpenter’s level).
⑤ Nothing should be fastened to screen frame or viewing surface.
⑥ Make sure you have received all parts (see parts list below and
exploded diagram on page 2).
⑦ Tools Required: Medium (#2) Phillips screwdriver (6" or greater shaft
length suggested). Optional tools: Flat blade screwdriver or small
putty knife.
⑧ Installer is responsible for providing appropriate hardware for mounting.
⑨ When lifting assembled screen, do not lift at only one corner; lift at
both corners. Lifting by one corner could result in damage to the
screen frame, especially on large screens.
⑩ The ideal temperature range for assembling folding screens to prevent
damaging the surface is 68°-78° F (20°-26° C). Assembling below
recommended temperatures may damage surface and void warranty.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Copyright © 2010 Draper Inc. Form Onyx_Inst10 Printed in U.S.A.
®
If you encounter any diffi culties installing or ser vic ing your Onyx screen, call your
dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.
Onyx—Hardware and Parts List
Frame Preparation
① Clean area and place frame assembly pieces face down. Insert plastic
corner pieces into ends of aluminum frame extrusions as indicated in
Figures 1 through 4. Secure each corner to each frame extrusion by
threading one #10-24 fastener through hole in plastic corner and into
rounded slot in aluminum frame extrusion.
Caution: Do not over-tighten fasteners—over-tightening could cause
damage to the frame corners.
Figure 1
② Secure corner pieces to aluminum frame extrusions with four (4) remaining
fasteners. Check to verify that all four (4) plastic corners are secure to
aluminum frame extrusion lengths and all eight (8) fasteners are tight (see
Fig. 5).
Caution: Do not over-tighten fasteners—over-tightening could cause
damage to the frame corners.
Figure 2
Frame Extrusions - 4
Frame Corners - 4
#10-24 fasteners - 8
Z-Brackets - 2
Viewing Surface - 1
Plastic Tubing - 4
Surface Retention
Extrusions- 4
Front
Back
Figure 3
Figure 5
Figure 4
(Continued on Page 2)
Patented by Draper, Inc., U.S. Patent Nos. 6,785,047; 7,113,332; and 7,369,310.
Caution: When lifting assembled screen, do not lift at only one corner; lift
at both corners. Lifting by one corner could result in damage to the screen
frame, especially on large screens.
Specyfikacje produktu
| Marka: | Draper |
| Kategoria: | Ekran projekcyjny |
| Model: | 253219 projection screen 253219 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Draper 253219 projection screen 253219, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Ekran projekcyjny Draper
10 Września 2024
6 Września 2024
4 Września 2024
2 Września 2024
2 Września 2024
1 Września 2024
31 Sierpnia 2024
31 Sierpnia 2024
29 Sierpnia 2024
29 Sierpnia 2024
Instrukcje Ekran projekcyjny
- Lumene
- Celexon
- Elite Screens
- Oregon Scientific
- Pyle
- Luxburg
- EluneVision
- Vestel
- AWOL Vision
- Stewart
- AV:link
- Projecta
- EPV
- Optoma
- ORAY
Najnowsze instrukcje dla Ekran projekcyjny
3 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
28 Stycznia 2025
11 Października 2024
8 Października 2024
8 Października 2024
7 Października 2024
6 Października 2024