Instrukcja obsługi Dürkopp Adler 2112
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dürkopp Adler 2112 (104 stron) w kategorii maszyna do szycia. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 6 użytkowników na średnio 4.5 gwiazdek
Strona 1/104
Service Instructions
All rights reserved.
Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents,
including extracts, is prohibited without the prior written approval of Dürkopp Adler AG.
Copyright © Dürkopp Adler AG 2020
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of Contents
Service Instructions 2112-5 - 00.0 - 02/2020 1
1 About these instructions ........................................................... 3
1.1 For whom are these instructions intended?.................................. 3
1.2 Representation conventions – symbols and characters ............... 3
1.3 Other documents .......................................................................... 4
1.4 Liability.......................................................................................... 5
2 Safety........................................................................................... 7
2.1 Basic safety instructions ............................................................... 7
2.2 Signal words and symbols used in warnings................................ 8
3 Clamp rail .................................................................................. 11
3.1 Assembling and disassembling the clamp rail............................ 11
3.2 Changing the toothed belt .......................................................... 12
4 Assembling and disassembling the cutter block .................. 14
5 Assistance transport................................................................ 15
5.1 Changing the toothed belt for the assistance transport .............. 15
5.2 Pin assignment for the stepper motor of the assistance
transport ..................................................................................... 17
6 Disassembling and assembling the control panel ................ 18
7 Setting up the machine ............................................................ 19
7.1 Adjusting the clamp rail .............................................................. 19
7.1.1 Adjusting the downforce pressure of the clamp rail.................... 19
7.1.2 Adjusting the disengagement position of the clamp slide........... 21
7.1.3 Adjusting the parallel orientation of the clamp rail ...................... 23
7.2 Adjusting the downforce pressure of the assistance transport ... 24
7.3 Adjusting the guide laser ............................................................ 25
7.4 Adjusting the folder..................................................................... 27
7.4.1 Aligning the folder parallel to the clamp rail................................ 27
7.4.2 Aligning the folder with the pick-up plate .................................... 28
7.4.3 Adjusting the lower position of the folder.................................... 29
7.5 Aligning the stop for the right fly piece........................................ 30
7.6 Adjusting the cutters ................................................................... 31
7.7 Adjusting the thread trimmer ...................................................... 32
7.8 Remaining thread monitor .......................................................... 33
7.9 Adjusting the photocell light sensitivity at the sewing head ........ 34
7.10 Adjusting the switches on the stepper motor PCB...................... 36
8 Programming ............................................................................ 39
8.1 Display and key functions........................................................... 39
8.2 Layout of the program control..................................................... 40
8.3 Overview of the program levels .................................................. 43
8.4 System menu.............................................................................. 44
8.4.1 Calling up and exiting the system menu..................................... 44
8.4.2 Entering the service code ........................................................... 45
8.4.3 Submenu Piece Counter ...................................................... 45
8.4.4 Submenu Eprom sewing parameters ................................. 46
8.4.5 Submenu Copy seam numbers .............................................. 47
8.4.6 Submenu Erase seam ............................................................. 48
8.4.7 Submenu Enter seam name .................................................. 48
Specyfikacje produktu
| Marka: | Dürkopp Adler |
| Kategoria: | maszyna do szycia |
| Model: | 2112 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Dürkopp Adler 2112, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje maszyna do szycia Dürkopp Adler
4 Marca 2025
13 Października 2024
11 Października 2024
6 Października 2024
29 Września 2024
28 Września 2024
25 Września 2024
23 Września 2024
22 Września 2024
20 Września 2024
Instrukcje maszyna do szycia
- maszyna do szycia Kohler
- maszyna do szycia Livoo
- maszyna do szycia Janome
- maszyna do szycia Prixton
- maszyna do szycia Silver
- maszyna do szycia Singer
- maszyna do szycia Weasy
- maszyna do szycia Prince
- maszyna do szycia Guzzanti
- maszyna do szycia Jocca
- maszyna do szycia Jata
- maszyna do szycia EasyMaxx
- maszyna do szycia Carina
- maszyna do szycia Anker-Bernette
- maszyna do szycia Bernette
Najnowsze instrukcje dla maszyna do szycia
8 Kwietnia 2025
5 Marca 2025
1 Marca 2025
24 Lutego 2025
24 Lutego 2025
24 Lutego 2025
24 Lutego 2025
18 Lutego 2025
17 Lutego 2025
11 Lutego 2025