Instrukcja obsługi Dürkopp Adler 630
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dürkopp Adler 630 (134 stron) w kategorii maszyna do szycia. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 9 użytkowników na średnio 3.7 gwiazdek
Strona 1/134
610-01/630-01
Service Instructions
All rights reserved.
Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents,
including extracts, is prohibited without the written approval in advance of Dürkopp Adler AG.
Copyright © Dürkopp Adler AG 2016
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of Contents
Service Instructions 610-01/630-01 - 02.0 - 12/2016 1
1 About these instructions ........................................................... 5
1.1 Scope of the instructions .............................................................. 5
1.2 Representation conventions – symbols and characters ............... 5
1.3 Other documents .......................................................................... 6
1.4 Liability.......................................................................................... 7
1.4.1 Transport ...................................................................................... 7
1.4.2 Proper use .................................................................................... 7
2 Safety instructions ..................................................................... 9
2.1 Basic safety instructions ............................................................... 9
2.2 Signal words and symbols used in warnings.............................. 11
3 Working basis ........................................................................... 15
3.1 Sequence of settings .................................................................. 15
3.2 Laying the cables........................................................................ 15
3.3 Removing covers........................................................................ 16
3.3.1 Tilting and re-erecting the machine head ................................... 16
3.3.2 Removing and fitting the head cover .......................................... 17
3.3.3 Removing and fitting the arm cover............................................ 18
3.3.4 Removing and fitting the covers on the base plate..................... 19
3.3.5 Removing and inserting the throat plate..................................... 20
3.3.6 Removing and inserting the top feed foot and sewing foot......... 21
3.3.7 Removing and installing the feeds.............................................. 22
3.3.8 Removing and fitting the oil pan ................................................. 23
3.3.9 Removing and fitting the upper belt guard.................................. 24
3.3.10 Removing and fitting the lower belt guard .................................. 25
3.4 Removing disruptive components .............................................. 26
3.4.1 Removing and installing the thread cutter .................................. 26
3.4.2 Removing and installing the needle protection........................... 28
3.4.3 Removing and installing the looper and looper mounting........... 29
3.5 Flat surfaces on shafts ............................................................... 30
3.6 Locking the machine................................................................... 30
4 Gauge and key set.................................................................... 33
5 Setting the adjusting disk to the arm shaft crank ................. 36
6 Setting the holding position of the machine.......................... 38
7 Setting the lower toothed belt wheel ...................................... 39
8 Setting the sewing foot ............................................................ 40
8.1 Setting the sewing foot stroke .................................................... 40
8.2 Setting the speed of the sewing foot lifting ................................. 41
9 Setting the looper ..................................................................... 42
9.1 Setting the rocker bolt and the left lower shaft bearing .............. 42
9.1.1 Draining and filling the oil in the looper drive housing ................ 43
9.1.2 Removing and fitting the looper drive housing ........................... 44
9.1.3 Setting the left lower shaft bearing ............................................. 45
9.1.4 Setting the rocker bolt................................................................. 46
9.2 Setting the looper drive housing................................................. 48
9.3 Setting the needle evasive movement (ellipsis width) ................ 49
9.3.1 Setting the needle evasive movement........................................ 50
Specyfikacje produktu
| Marka: | Dürkopp Adler |
| Kategoria: | maszyna do szycia |
| Model: | 630 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Dürkopp Adler 630, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje maszyna do szycia Dürkopp Adler
4 Marca 2025
13 Października 2024
11 Października 2024
6 Października 2024
29 Września 2024
28 Września 2024
25 Września 2024
23 Września 2024
22 Września 2024
20 Września 2024
Instrukcje maszyna do szycia
- maszyna do szycia Elna
- maszyna do szycia ER
- maszyna do szycia Juki
- maszyna do szycia SteamMax
- maszyna do szycia Necchi
- maszyna do szycia Prince
- maszyna do szycia RCE
- maszyna do szycia Sinbo
- maszyna do szycia Zippy
- maszyna do szycia Emerio
- maszyna do szycia Primera
- maszyna do szycia Blaupunkt
- maszyna do szycia Bernette
- maszyna do szycia Pfaff
- maszyna do szycia Kayser
Najnowsze instrukcje dla maszyna do szycia
8 Kwietnia 2025
5 Marca 2025
1 Marca 2025
24 Lutego 2025
24 Lutego 2025
24 Lutego 2025
24 Lutego 2025
18 Lutego 2025
17 Lutego 2025
11 Lutego 2025