Instrukcja obsługi Dürkopp Adler 670
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dürkopp Adler 670 (140 stron) w kategorii maszyna do szycia. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 8.5 użytkowników na średnio 5.0 gwiazdek
Strona 1/140
670/680
Service Instructions
All rights reserved.
Property of Dürkopp Adler GmbH and protected by copyright. Any reuse of these contents,
including extracts, is prohibited without the prior written approval of Dürkopp Adler GmbH.
Copyright © Dürkopp Adler GmbH 2021
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of contents
Service Instructions 670/680 - 04.0 - 06/2021 1
1 About these instructions ........................................................... 5
1.1 For whom are these instructions intended?.................................. 5
1.2 Representation conventions – symbols and characters ............... 5
1.3 Other documents .......................................................................... 7
1.4 Liability.......................................................................................... 7
2 Safety........................................................................................... 9
2.1 Basic safety instructions ............................................................... 9
2.2 Signal words and symbols used in warnings.............................. 10
3 Working basis ........................................................................... 13
3.1 Order of the settings ................................................................... 13
3.2 Laying the cable guide................................................................ 13
3.3 Gages ......................................................................................... 14
3.4 Removing the covers.................................................................. 16
3.4.1 Access to the underside of the machine..................................... 16
3.4.2 Removing the arm cover ............................................................ 17
3.4.3 Removing the head cover........................................................... 18
3.4.4 Removing the valve cover .......................................................... 19
3.4.5 Removing the rear cover ............................................................ 20
3.5 Flats on shafts ............................................................................ 20
3.6 Locking the machine in place ..................................................... 21
3.7 Setting the handwheel into position............................................ 23
4 Setting the handwheel scale ................................................... 25
5 Positioning the arm shaft......................................................... 26
6 Positioning the toothed belt wheels ....................................... 27
6.1 Positioning the upper toothed belt wheel.................................... 28
6.2 Positioning the lower toothed belt wheel .................................... 29
7 Stitch length adjusting wheels................................................ 30
7.1 Setting the upper stitch length adjusting wheel .......................... 30
7.2 Setting the synchronization of top and bottom feed ................... 32
7.3 Setting the lower stitch length adjusting wheel........................... 33
7.4 Setting the stitch length limit....................................................... 34
7.5 Setting the eccentric for the forward and backward stitches ...... 35
7.6 Setting the feed dog bar ............................................................. 36
7.7 Setting the initial position of the feed gear.................................. 37
8 Needle bar linkage.................................................................... 39
8.1 Aligning the needle bar linkage sideways................................... 39
8.2 Setting transmission lever .......................................................... 41
8.3 Setting the thread lever .............................................................. 42
9 Post bed feed ............................................................................ 43
9.1 Aligning the post bed feed .......................................................... 43
9.2 Setting the feed dog feed movement.......................................... 45
9.3 Setting the feed dog stroke movement....................................... 46
9.4 Setting the feed dog height......................................................... 47
9.5 Setting the compensating weight................................................ 48
9.6 Setting the needle penetration in the feed direction ................... 49
Specyfikacje produktu
| Marka: | Dürkopp Adler |
| Kategoria: | maszyna do szycia |
| Model: | 670 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Dürkopp Adler 670, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje maszyna do szycia Dürkopp Adler
4 Marca 2025
13 Października 2024
11 Października 2024
6 Października 2024
29 Września 2024
28 Września 2024
25 Września 2024
23 Września 2024
22 Września 2024
20 Września 2024
Instrukcje maszyna do szycia
- maszyna do szycia Guzzanti
- maszyna do szycia Lifetec
- maszyna do szycia W6
- maszyna do szycia Kenmore
- maszyna do szycia Janome
- maszyna do szycia Müller
- maszyna do szycia Jata
- maszyna do szycia Siemssen
- maszyna do szycia Mellerware
- maszyna do szycia Gritzner
- maszyna do szycia Micromaxx
- maszyna do szycia Minerva
- maszyna do szycia TriStar
- maszyna do szycia ER
- maszyna do szycia Hema
Najnowsze instrukcje dla maszyna do szycia
8 Kwietnia 2025
5 Marca 2025
1 Marca 2025
24 Lutego 2025
24 Lutego 2025
24 Lutego 2025
24 Lutego 2025
18 Lutego 2025
17 Lutego 2025
11 Lutego 2025