Instrukcja obsługi Extech MN36
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Extech MN36 (2 stron) w kategorii multimetr. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 6 użytkowników na średnio 4.4 gwiazdek
Strona 1/2
MN36- -US_V2.3 10/20 en
Safety
This symbol, adjacent to another symbol or terminal, indicates
the user must refer to the manual for further information.
This symbol, adjacent to a terminal, indicates that, under
normal use, hazardous voltages may be present
Double insulation
1. Improper use of this meter can cause damage, shock, injury or death.
Read and understand this user manual before operating the meter.
2. Make sure any covers or battery doors are properly closed and ured.
3. Always remove the test leads before replacing the battery or fuses.
4. Inspect the condition of the test leads and the meter itself for any
damage before operating the meter. Repair any damage before use.
5. Do not exceed the maximum rated input limits.
6. Use great care when making measurements if the voltages are
greater than 25VAC rms or 35VDC. These voltages are considered a
shock hazard.
7. Always discharge capacitors and remove power from the device
under test before performing Diode, Resistance or Continuity tests.
8. Remove the battery from the meter if the meter is to be stored for
long periods.
9. To avoid electric shock, do not measure AC current on any circuit
whose voltage exceeds 250V AC.
Input Limits
Function
Maximum Input
VDC, VAC
600V AC/600V AC
Resistance, Diode, Continuity
500V DC/AC
mA DC
200mA DC
10A DC
10A DC (15 seconds max.
every 15 min.)
Frequency
250V DC/AC
Two-year Warranty
FLIR Systems, Inc. warrants this Extech brand instrument to be free
of defects in parts and workmanship for from date of two years
shipment (a six-month limited warranty applies to sensors and cables).
To view the full warranty text please visit:
http://www.extech.com/support/warranties.
Calibration and Repair Services
FLIR Systems, Inc. oers calibration and repair services r the fo
Extech brand products we sell. We oer NIST traceable calibration for
most of our products. Contact us for information on calibration and repair
availability, refer to the contact information below. Annual calibrations
should be performed to verify meter performance and accuracy. Product
specications are subject to change without notice. Please visit our
website for the most up- -date product information: . to www.extech.com
Contact Customer Support
Customer Support Telephone List: https://support.ir.com/contact
Calibration, Repair and Returns, : repair@extech.com
Technical Support: https://support.ir.com
Copyright 2004-2020 FLIR Systems, Inc. ©
All rights reserved including the right of reproduction in whole or in part
in any form
www.extech.com
User Manual
MiniTecTM Series
Model MN36
Auto-Ranging Mini MultiMeter
Introduction
Congratulations o Auto-Ranging n your purchase of Extech’s MN36
Multimeter. This meter measures AC/DC Voltage, AC/DC Current,
Resistance, Capacitance, Frequency, Temperature, Diode Test and
Continuity. Proper use and care of this meter will provide many years of
reliable service.
Specications
Accuracy Stated at 73oF 10oF (23oC 5 oC) and less than
70% RH
Diode Test Test current of 0.6mA maximum, open circuit
voltage 1.5V DC typical
Continuity Check Audible signal will sound if the resistance is less
than approximately <8
Temperature sensor Requires type K thermocouple
Input Impedance 10M AC/ ) (V DC
Display 3999 count LCD
Overrange is displayed “OL”
Polarity Automatic (no indication for positive polarity);
Minus (-) sign for negative polarity.
Measurement Rate 3 times per second, nominal
Low Battery “ ” is displayed if battery voltage drops below
operating voltage
Batteries Requires (2) AAA batteries
Fuses mA range; 250mA/250V fast blow
10A range, no protection
Operating Temp 32oF to 104o
F (0 oC to 40oC)
Storage Temp -4o
F to 140 o
F (-20 o
C to 60 oC)
Relative Humidity Maximum relative humidity 80% for temperatures
up to 31 C decreasing linearly to 50% relative °
humidity at 40 °C.
Operating Altitude 7000ft (2000 meters) maximum
Weight 5.4 oz. (153g).
Size 138mm x 72mm x 38mm) 5.43” x 2.83” x 1.5” (
Safety For indoor use and in accordance with
Overvoltage Category II, Pollution Degree 2.
Category II includes local level, appliance,
portable equipment, etc., with transient
overvoltages less than Overvoltage Category III
Specications
Function
Range
Accuracy
DC Voltage
(V DC)
4 00.0mV
(0.5% reading + 4 digits)
4.000V
(0.8% reading + 4 digits)
40.00V
400.0V
600V
AC Voltage
(V AC)
50-60Hz
40-400Hz
4.000V
(0.8% rdg + 4 d)
(2% rdg + 5 d)
40.00V
(1.2% rdg + 5 d)
400.0V
600V
DC Current
400.0µA
(1.2% reading + 4 digits)
4000µA
40.00mA
200.0mA
10A
(2.5% reading + 4 digits)
AC Current
(40 to 400Hz)
400.0µA
(1.5% reading + 5 digits)
4000µA
40.00mA
200.0mA
10A
(3% reading + 5 digits)
Resistance
4 00.0
(1.2% reading + 4 digits)
4.000k
40.00k
4 k 00.0
4.000M
20.00M
(3.0% reading + 5 digits)
Capacitance
4.000nF
Not specied
40.00nF
(3.0% reading + digits) 10
400.0nF
4.000µF
40.00µF
Not Specied
100µF
Frequency
10.00Hz
(1.0% reading + 4 digits)
10Hz to 1MHz
Sensitivity: 5.0Vrms
100Hz
1.000kHz
10.00kHz
100.0kHz
1.000MHz
5.000MHz
Not specied
Temp F
Temp C
-40 to
1400 F
-20 to 750 C
-40 to 650°F; (1.0% rdg + digits) 10
651 00 10 to 14 °F; (3% rdg + digits)
-20 to 400 C; (1.0% rdg + digits) 10
400 to 750 C; (3% rdg + digits) 10
(probe accuracy not included)
Specyfikacje produktu
| Marka: | Extech |
| Kategoria: | multimetr |
| Model: | MN36 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Extech MN36, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje multimetr Extech
22 Grudnia 2024
29 Września 2024
29 Września 2024
29 Września 2024
29 Września 2024
24 Września 2024
19 Września 2024
18 Września 2024
14 Września 2024
14 Września 2024
Instrukcje multimetr
- PeakTech
- Etekcity
- Pyle
- HT Instruments
- Wiha
- TFA
- Brandson
- Sanwa
- Kyoritsu
- Laserliner
- Qian
- Caltek
- Owon
- Micronta
- PCE Instruments
Najnowsze instrukcje dla multimetr
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
28 Marca 2025
26 Marca 2025
14 Marca 2025