Instrukcja obsługi GE UDT165SIVII
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE UDT165SIVII (2 stron) w kategorii pralka. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 3.5 użytkowników na średnio 4.7 gwiazdek
Strona 1/2
Bracket
Spacer Pad Spacer
3/4" Thick Custom Panel
Template Instructions for
18" Top Control Integrated
Dishwasher Models
The custom panel should be sized to your installation situation. See Step 1. For easier installation, the
custom panel and custom handle should be attached before installing the dishwasher. Use this template
to locate mounting screws and spacers on the custom panel.
IMPORTANT
• A custom handle must be installed onto the custom
panel. Install the custom handle 4-1/2" max. from the
top of the panel.
STEP 2 DRAW CENTERLINE
• Placethecustompanelonaatsurfacewiththe
appearancesidedown.
• Locatetheverticalcenterofthepanelatthetop.
• Useacarpenter'ssquaretodrawacenterlinefrom
toptobottom.
STEP 3 ALIGN TEMPLATE TO PANEL
• Trimtemplateonthedottedlinealongallsides.
• Placethetemplateonthepanelalignedwiththetop
edgeandthecenterline.Usetapetoholdinplace.
IMPORTANT: If the template is not aligned with the top
edge of the panel, the 1/2" (1.27 cm) minimum gap will not
be maintained. This 1/2" (1.27 cm) minimum gap must be
maintained to prevent condensation and damage to the
control panel from screw heads.
• Useanawltomarkthescrewholelocationsindicated
onthetemplate.Removethetemplate.
HEIGHT
Panel height should be 26-13/16" (68.1 cm).
• Thetopofthecustompanelmustbeush
withthetopofthedoor.The1/2"(1.27cm)
minimumgapbetweenthetopofthedoorand
thebottomofthecountertopmustbemaintained.
PARTS INCLUDED:
(2) Brackets
(4) 5/8" (1.58 cm) Phillips at-head screws
(2) Spacer pads
(2) Metal spacers
(2) 1" (2.54) Phillips at-head screws
(2) 1-1/2" (3.81 cm) Phillips at-head screws
STEP 1 CUSTOM PANEL SIZE REQUIREMENTS
IMPORTANT: To ensure optimum door balance
performance, the custom panel must not weigh
more than 8 lbs.
WIDTH
Panel width must be 17-1/2" (44.4 cm).
• Ifthepanelwidthislessthan17-1/2"(44.4cm),it
willnotcoverthedishwasherframe.
STEP 7 CHECK DOOR BALANCE
Tocheckthedoorbalance,holdthetopofthe
dishwasherrmly.
• Checkthedoorbalancebyopeningand
closingthedoor.
• Ifthedoordropswhenreleased,increasethe
springtension.Ifthedoorriseswhenreleased,
decreasethespringtension.
• UsingaT25torquedriverorsocketwrench
(asappropriate),adjustinthedirectionshown.
Adjustbothsidesequally.
STEP 6 INSTALL ASSEMBLED PANEL
• Securethepaneltothedoorbyinserting
the top metal spacers and bottom brackets
intothematchingslotsonthedishwasher
doorandcontrolpanel.
• Make sure both metal spacers
andbothbracketsengagetheslots.
• Pressthepanelagainstthedoorandpush
downwarduntilthemetalspacersandbrackets
arefullyengagedintotheslots.Thepanel
shouldalignevenlywiththetopandsides.
• Standthedishwasherupright.
• Openthedishwasherdoorandremovetherst
sidescrewfromthetoponeachsideoftheinner
door.
•Replacethesescrewswiththe1-1/2”(3.81cm)
Phillipsat-headedscrewsanddrivethemthrough
theinnerdoorandintothecustompanel.
IMPORTANT: Donotovertightenscrews.
Excessivetighteningofthescrewscoulddamage
dooredges.
STEP 5 INSTALL CUSTOM HANDLE
Acustomhandlemustbeinstalledontothepanel
beforethepanelissecuredtothedishwasherdoor.
• Thehandleshouldbeinstalledsothatitaligns
withadjacentdrawerhandles,or4-1/2"(115mm)
max.fromthetopofthepanel.Securethehandle
inthesamemannerasthecabinethandles.
Screwsmustbecountersunkintothepanel.
STEP 4 INSTALL MOUNTING SCREWS AND SPACERS
Note:Thecustompanelissecuredtothedishwasherdoor
withthemetalspacers,screwsandbracketsprovided.
Themetalspacersandbracketswillslipintotheslots
onthedishwasherdoorandcontrolpanel.
• Alignthemetalspacersoverthetoppilotholes.Ensure
thethick,recessedsideisfacingup.
• Drivethesupplied1"(2.54cm)Phillipsat-headscrews
throughthemetalspacersandintothepanel.
• Alignthebracketsoverthebottompilotholes.Ensure
thecurvedlipisfacingup.Ifthesurfaceofthe
panelisnotat,usethespacerpadsprovided.
• Drivethe5/8"(1.58cm)Phillipsat-headscrewsthrough
thebracketsandintothepanel.
Countertop
Minimum1/2"(1.27cm)
gapforclearance
1/2"(1.27cm)minimum
Mark center
screwholes
Handle
41/2"
(115mm)
Max.
fromtop
ofpanel
Custom
door panel
Screwsmustbe
countersunkintopanel
PARTS SUPPLIED
(2)Brackets
(2)1-1/2"(3.81cm)
Phillipsat-head
screws
(2)Metalspacers (2)SpacerPads
(Optional)
(2)1"(2.54cm)
Phillipsat-head
screws
(4)5/8"(1.58cm)
Phillipsat-head
screws
0120501700
Custom
panel
Dishwasher
door
Custom panel
Top of Panel
7-11/16"
2-5/32"
(5.5 cm)
(19.5 cm)
Trim Around Dotted Line
Drill 3/32"
Pilot Hole
3/32" Deep
Top of Panel
7-11/16"
2-5/32"
(5.5 cm)
(19.5 cm)
Drill 3/32"
Pilot Hole
3/32" Deep
Drill 3/32"
Pilot Hole
3/32" Deep
13/32"
(1 cm)
6-1/2"
(16.5 cm)
5-29/32"
(15 cm)
Drill 3/32"
Pilot Hole
3/32" Deep
13/32"
(1 cm)
6-1/2"
(16.5 cm)
5-29/32"
(15 cm)
Trim
Around
Dotted
Line
31-4000281Rev1
11-22GEA
Turn
clockwise
toincrease
Turn
counterclockwise
to decrease
Adjustbothsidesequally
Specyfikacje produktu
| Marka: | GE |
| Kategoria: | pralka |
| Model: | UDT165SIVII |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z GE UDT165SIVII, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje pralka GE
2 Kwietnia 2025
13 Stycznia 2025
12 Stycznia 2025
15 Grudnia 2024
15 Października 2024
14 Października 2024
8 Października 2024
7 Października 2024
6 Października 2024
6 Października 2024
Instrukcje pralka
- Signature
- Edy
- SanGiorgio
- Hilton
- Dexter Laundry
- Hyundai
- Primo
- Smart Brand
- Technika
- Nordmende
- Ignis
- Rosieres
- Quigg
- Elektra Bregenz
- Speed Queen
Najnowsze instrukcje dla pralka
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025