Instrukcja obsługi GE ZDIC150WBB
GE
Maszyna do lodu
ZDIC150WBB
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE ZDIC150WBB (18 stron) w kategorii Maszyna do lodu. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 6 użytkowników na średnio 4.3 gwiazdek
Strona 1/18
Installation
Instructions
Automatic Ice maker
ZDIC150
ZDIS150
Design Guide
With Installation Instructions
monogram.com
Installation Instructions
• BEFORE YOU BEGIN:
Read these instructions completely and carefully.
• IMPORTANT:
Save these instructions for local inspector’s use.
• IMPORTANT:
Observe all governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
WARNING:
This appliance must be properly grounded.
Failure to do so can result in death, fire or electrical
shock. See “Power Supply,” page 6.
AVERTISSEMENT :
Cet appareil doit être correctement mis à la terre.
Le non-respect de ces instructions peut causer la
mort, un incendie ou un choc électrique. Consulter «
Alimentation électrique », page 6.
If you received a damaged ice maker, you should
immediately contact your dealer or builder.
Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty.
See the Owner’s Manual for warranty information.
• Use this appliance only for its intended purpose.
Check with local utilities for electrical codes that
apply in your area. Local codes vary. Installation,
electrical connections and grounding must comply
with applicable codes. In the absence of local codes,
the ice maker should be installed in accordance
with National Electrical Code ANSI/NFPA 70-1990 or
latest edition.
For Monogram local service in your area, call
1.800.444.1845.
For Monogram Service in Canada, call
1.800.561.3344.
For Monogram Parts and Accessories, call
1.800.626.2002.
2
CONTENTS
Design Information
Models Available .................................................................... 3
Optional Accessories ........................................................... 3
Tools and Materials Required ........................................ 3
Cutout & Product Dimensions .........................................4
Installation
Advance Planning .................................................................4
Water Supply ........................................................................... 5
Power Supply ........................................................................... 6
Remove Packaging ............................................................... 6
Water Filtration System ................................................. 6, 7
Adjust Height of Ice maker ...............................................7
Connect the Drain ................................................................. 9
Connect Water Supply to Appliance ............................9
Reverse Door Swing ...................................................10, 11
Accessories
ZPK2 Auxiliary Pump Kit ............................................ 12-15
ZIP75BB Kit for 3/4” thick panels ..........................16, 17
Design Information
MODELS AVAILABLE
ZDIC150ZBB, ZDIS150ZSS
Available in black and stainless steel.
The ice maker may be installed below a countertop
or used free-standing.
3
OPTIONAL ACCESSORIES
=,3%%³For the installation of a trimless
3/4” thick custom panel on black models (not for
stainless steel models). This kit provides a handle
that can be installed with the custom panel.
A custom handle of your choice may be installed onto
the 3/4” panel. See installation instructions
on pages 10 and 11.
ZPK2 Drain Pump Kit - For use when a floor drain is
not available. The drain pump must be installed
inside the unit and can pump discharge water at a
maximum vertical height of 10 feet. 10 feet of tubing
is supplied with the kit.
TOOLS AND MATERIALS REQUIRED FOR BASIC INSTALLATION
• 1/4” socket
• 3/4” adjustable wrench
• Level
• GE SmartConnect™ Refrigerator Tubing Kit or 1/4” O.D.
copper tubing, of sufficient length to reach the installation
• Flat-blade screwdriver
• 7/16” and 1/2” open-end wrenches or 2 adjustable wrenches
• 1/4” nut driver
Specyfikacje produktu
| Marka: | GE |
| Kategoria: | Maszyna do lodu |
| Model: | ZDIC150WBB |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z GE ZDIC150WBB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Maszyna do lodu GE
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
29 Września 2024
14 Września 2024
4 Września 2024
3 Września 2024
1 Września 2024
29 Sierpnia 2024
Instrukcje Maszyna do lodu
- Maszyna do lodu Taurus
- Maszyna do lodu Maytag
- Maszyna do lodu Solis
- Maszyna do lodu Marvel
- Maszyna do lodu Electrolux
- Maszyna do lodu Lynx
- Maszyna do lodu Norpole
- Maszyna do lodu KitchenAid
- Maszyna do lodu Steba
- Maszyna do lodu Heinner
- Maszyna do lodu Viking
- Maszyna do lodu Cattabriga
- Maszyna do lodu Petra Electric
- Maszyna do lodu Melissa
- Maszyna do lodu Thermostar
Najnowsze instrukcje dla Maszyna do lodu
12 Stycznia 2025
11 Stycznia 2025
11 Stycznia 2025
11 Stycznia 2025
11 Stycznia 2025
11 Stycznia 2025
10 Stycznia 2025
10 Stycznia 2025
10 Stycznia 2025
9 Stycznia 2025