Instrukcja obsługi Gemini 7462
Gemini
alarm samochodowy
7462
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Gemini 7462 (10 stron) w kategorii alarm samochodowy. Ta instrukcja była pomocna dla 19 osób i została oceniona przez 10 użytkowników na średnio 4.9 gwiazdek
Strona 1/10
DESCRIPTION
The systems 7463 7462and are modular systems which consists of an alarm unit and one audible external
siren. These alarm systems can be installed on vehicles with 12V battery with negative to earth.
FUNCTIONS
7463
- - Self powered unit and remote controlled alarm with dynamic code (frequency 433.92 MHz).
- Blinker and external siren.
- Negative control for additional siren.
- Central door locking, windows and electric sunroof control (for vehicles with “Pac -comfort” system).
- Perimetric, volumetric (K1 and K2 model ) protection.
- Alarm memory through audible and optical signalisations.
- Remote controlled “PANIC” function.
- Emergency disarming through “PIN” code.
- Accessorial functions programmable with the transmitter.
7462- As 7463 not self-powered.
INSTALLATION INSTRUCTIONS
- Connect the power wire to the battery positive terminal and the earth directly to the bodywork of
the vehicle.
- Connect always the alarm GREEN-BROWN wire to the door pin switches.
- Connect always the alarm GREEN wire to the bonnet switch.
- On catalysed vehicles the engine immobilisation must be carried out on the fuel pump.
- If an ultrasonic module is used, the ultrasonic heads must be positioned on the left and right
windscreen pillar of the rear windows, turned to the passenger’s compartment and away from the
facia outlet.
- After the electric connections have been carried out, programme the functions through the
transmitter and change the manufacturer “PIN” code.
WIRING CONNECTIONS
(DISCONNECT THE BATTERY NEGATIVE TERMINAL AND ONLY RECONNECT AFTER THE INSTALLATION IS
COMPLETE)
FUNCTION WIRE COLOUR
Earth ðð BLACK initialled “M”
Battery positive terminal ðð BLACK initialled “R”
Command for external relais ðð 2 x BLACK initialled “H”
Ignition live ðð YELLOW
Direction indicator lights ðð 2 x ORANGE
Door and boot pin switches ðð GREEN-BROWN
Bonnet switch ðð GREEN
Positive alarm armed ðð PINK
Sensors inlet ðð GREEN-BLACK
Negative outlet control additional siren
ðð YELLOW-BLACK
Central door locking ðð YELLOW- -BLUE, RED BLUE, YELLOW-GREY,
RED- - -GREY, YELLOW BROWN, RED BROWN
Sound unit ðð BLUE and GREY
NOTE: in the wiring harness there are 2 connectors; connect the 4-pin connector to the ultrasonic or high
frequency module and the 2-pin connector to the LED.
The terminals of the Blue and Green wire of the sound unit must be positioned in the White connector of
the unit on positions 10 and 20. In the kit there is an extension of the BLACK initialled V wire for the
connection of the bonnet b utton.
FUNCTIONS PROGRAMMABLE THROUGH THE TRANSMITTER
FUNCTIONS MANUFACTURER’S PROGRAMMING
1 Arming / disarming audible tones Activated
2 Panic alarm / Car Finder Panic activated
3 Current sensor De-activated
4 Automatic alarm rearming /
Automatic locking of the doors
De-activated
5 Passive alarm arming De-activated
6 CDL pulse time Selected time 1 second
7 Comfort time De-activated
8 CDL opening double pulse De-activated
INLET IN THE PROGRAMMING PROCEDURE OF THE ACCESSORIAL FUNCTIONS.
Disarm the alarm with the transmitter, open the vehicle’s door (keep it opened) and turn the ignition
key to ON: the LED will switch on for 0,5 seconds.
During this period (led switched on) press at the same time on both transmitter’s button.
The confirmation of the programming phase inlet is given by the Led switching on with fix light followed
by two acoustic signalling; one with low frequency (BOP) and one with high frequency (BIP).
The system now is in the programming modality and it is waiting for the controls that will be sent with
the transmitter’s buttons.
CHANGE OF THE FUNCTIONS PROGRAMMING.
Any selection will be signalled by two different audible tones:
REMOTE CONTROL PUSH BUTTON N°1 : HIGH FREQUENCY AUDIBLE TONE (BIP). TO SET ON THE
CURRENT FUNCTION AND SELECT THE NEXT ONE.
REMOTE CONTROL PUSH BUTTON N°2 : LOW FREQUENCY AUDIBLE TONE (BOP). TO SET OFF THE
CURRENT FUNCTION AND SELECT THE NEXT ONE.
Push Button N° 1: Set ON
ARMING / DISARMING AUDIBLE TONES Push Button N° 2: Set OFF
Push Button N° 1: Panic set ON
Car finder set OFF
PANIC ALARM / CAR FINDER Push Button : Panic set OFF
Car finder set ON
Push Button N° 1: Set ON
CURRENT SENSOR Push Button N° 2: Set OFF
Push Button N° 1: Set ON
AUTOMATIC ALARM REARMING / AUTOMATIC
LOCKING OF THE DOORS Push Button N° 2: Set OFF
Push Button N° 1: Set ON
PASSIVE ALARM ARMING Push Button N° 2: Set OFF
Push Button 1: 6 seconds
CDL PULSE TIME Push Button 2: 1 second
Push Button N° 1: Set ON
COMFORT TIME Push Button N° 2: Set OFF
Push Button N° 1: Set ON
CDL OPENING DOUBLE PULSE Push Button N° 2: Set OFF
Specyfikacje produktu
| Marka: | Gemini |
| Kategoria: | alarm samochodowy |
| Model: | 7462 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Gemini 7462, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje alarm samochodowy Gemini
23 Września 2024
23 Września 2024
20 Września 2024
15 Września 2024
14 Września 2024
14 Września 2024
13 Września 2024
13 Września 2024
13 Września 2024
13 Września 2024
Instrukcje alarm samochodowy
Najnowsze instrukcje dla alarm samochodowy
9 Kwietnia 2025
1 Października 2024
1 Października 2024
1 Października 2024
27 Września 2024
24 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024