Instrukcja obsługi Hunter Classic Original 23855

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hunter Classic Original 23855 (4 stron) w kategorii Wentylator. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 6 użytkowników na średnio 4.4 gwiazdek

Installation in concrete ceiling

CAUTION:

For concrete mounting, the drilled hole must be recommend-

ed by the manufacturer of the anchor (this is usually marked

on the anchor) and must be drilled at least 1/2" deeper than

the length of the anchor.

The holes must be made with a suitable carbide-tipped

masonry drill bit.

The anchors must be new and unused.

The concrete ceiling must be sound and free of cracks or

voids in the vicinity of the mounting holes.

The anchors must be set in flush with the surface of the

concrete.

The bracket screws must never be backed out. If the bracket

screws can be turned easily (by hand), do not hang fan.

Installation

Drill holes 2" deep in concrete ceiling to receive 1/4" x 11

/2"

expansion shield anchor, “Rawl No. 1055” or equal. (Not fur-

nished.) Install shield in holes, observing all cautions above.

Proceed with the installation of the fan per the basic installa-

tion instructions.

The Inside Story

Oil is constantly pumped up the spiral groove to lubricate the

rotor and shaft. The oil is returned to the reservoir where the

bearings are submerged in a bath of oil.

This unique lubrication system is built into all Original Hunter

Ceiling Fans. That’s one reason Hunters last so long. And why

we can offer a Limited Lifetime Warranty.

Fill in the blanks below for your record.

Serial number

Model number

Date purchasedDate installed

Dealer/store name where purchased

4

41121-01 9/95

Trouble shooting guide

ProblemProbable CauseSolution

1. Nothing1. Power turned1. Turn power on or

happens;off or fusereplace fuse.

blades doblown.

not rotate.*2. Loose wire2. Loosen canopy.

connectionsCheck all

or wrongconnections (turn

connections.power off while

checking).

3. Pull chain3. Pull switch cord.

switch not

“on”.

4. Reversing4. Slide reversing

switch inswitch either up or

center. down.

* Note: If blades will not turn by hand, contact your nearest

service representative or dealer.

1. Noisy1. Blade irons1. Tighten screws until

operation. looselysnug.

screwed to

rotor.

2. Blade2. Tighten.

screwed

loosely to

blade iron.

3. Blade cracked.3. Replace all 4 blades.

Contact dealer.

4. Canopy4. Lower canopy.

contacting

ceiling.

5. No oil or low5. Check oil level.

oil level.

1. Excessive1. Unbalanced1. Rebalance (See

wobblingblades.Step 7D).

2. Inadequate2. Relocate fan.

blade

clearance.

3. Loose blades3. Tighten all screws.

or blade irons.

4. Fan not4. Turn power off.

secure onSupport fan very

hangercarefully. Loosen

assembly.canopy and hang

correctly.

1.

2.

3.

4.

5.

6.

A.

B.

HUNTER FAN COMPANY

2500 FRISCO AVENUE

MEMPHIS, TN 38114

®

Fig. 18

Hanger

Bracket Bracket

Power

Leads

Used With

Light Kit

Canopy

Set Screw

Oil Filler Hole

Oil Return

Rotor

Field

Windings Oil Reservoir

Bearing Nut

Switch Housing Cover

Bushing Pin

Ground Screw

Pipe Nipple (Std.)

Shaft

Cast Iron

Fan Housing

Cast Metal

Lower

Cover

Spiral

Groove

Bearings

Switch Housing

Pull Chain

Switch

expansion

shield anchor

set flush with

ceiling (anchor

not furnished)

Concrete ceiling

Bracket

(Furnished with fan)

Fig. 17

Specyfikacje produktu