Instrukcja obsługi ICOM HM-157B
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla ICOM HM-157B (11 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 27 osób i została oceniona przez 14 użytkowników na średnio 5.0 gwiazdek
Strona 1/11
INSTRUCTIONS
REMOTE-CONTROL MICROPHONE
HM-157
Thank you for purchasing the HM-157
REMOTE
-
CONTROL MICROPHONE
. The COMMANDMIC IITM is a
remote control microphone for use with the IC-M602,
M504, M422, M402 or else.
Please read these instructions and transceiver’s
instruction manual carefully before installation and
operation.
■Panel description
The HM-157 remotely controls the transceiver and provides an
optional Intercom function.
zPOWER KEY [PWR]
Push for 2 sec. to turn the HM-157 power ON or OFF when
the transceiver power is turned ON.
xSCAN KEY [
[SCANSCAN](
]( )
)
➥Push to start and stop Normal or Priority scan when TAG
channels are programmed.
➥Push for 1 sec. to set the displayed channel as a TAG
(scanned) channel.
➥While pushing [
[H/L
H/L]
], push for 3 sec. to clear or set all TAG
channels.
cTRANSMIT POWER KEY [[H/L
H/L]]
➥Push to toggle high or low power.
• Some Channels are set to low power only.
➥While pushing this key, other keys perform secondary func-
tions.
➥While turning power ON, push to toggle the All key lock
function ON or OFF.
• “T” blinks while the All key lock function is in use.
• Only [
[PWR
PWR] ]and [
[PTT
PTT] ]function when the All key lock func-
tion is in use.
vPTT SWITCH [
[PTT
PTT]
]
Push and hold to transmit; release to receive.
bCHANNEL UP/DOWN KEYS [
[Y
Y
Y
Y
YY
Y
Y
Y
Y
YY]
]/[
[Z
Z
Z
Z
ZZ
Z
Z
Z
Z
ZZ]
]
➥Push either key to select the operating channel, Set mode
settings, etc.
➥After pushing [
[VOL
VOL] ]or [
[SQL
SQL]
], push either key to adjust
audio level or noise squelch level, respectively.
➥After pushing [
[VOL
VOL] ]for 1 sec, push either key to adjust
the brightness of the LCD and key backlight.
➥Checks TAG channels or changes scanning direction dur-
ing scan.
➥Push either key to adjust the audio level during in Hailer
(Public Address)* mode. (* Depends on the transceiver)
➥While pushing
[VOL](
[VOL]( P
PA/RX
A/RX )
)
push either key to
adjust the audio level during in RX Speaker mode.
nCHANNEL 16/CALL CHANNEL KEY [
[](
](99)
)
➥ Push to select Channel 16.
➥ Push for 1 sec. to select call channel.
• “CALL” appears when call channel is selected.
➥Push for 3 sec. to enter call channel programming condi-
tion when call channel is selected.
➥While pushing [
[H/LH/L]
], enters channel comments program-
ming condition.
➥While turning power ON, push to enter Set mode.
mCHANNEL/DUALWATCH/TRI-WATCH KEY
[[CH/WX
CH/WX](]( U/I/C)U/I/C)
➥Push to select and toggle the regular channels and
weather channels.
➥While pushing [[H/L
H/L]
], push to select one of three channel
groups in sequence.
• U.S.A., International and Canadian channels are available.
➥Push for 1 sec. to start Dualwatch or Tri-watch.
➥Stops Dualwatch or Tri-watch when either is activated.
,ATTENUATOR/INTERCOM/SCRAMBLER* KEY
[
[LO/DXLO/DX ](
]( SCR)
SCR)
➥Push to toggle the Attenuator function ON or OFF.
• “LOCAL” appears when the Attenuator is in use.
➥Push for 1 sec. to activate the Intercom function.
➥Calls the transceiver when pushed and held while in Inter-
com mode.
➥While pushing [
[H/LH/L ]
], activates an optional Voice scram-
bler* function.
• The Voice scrambler function cannot be used on Ch 16 and 70.
* The Voice scrambler function is available depends on the
transceiver.
.SQUELCH/MONITOR/LOCK KEY [[SQL
SQL](]( L)L)
➥After pushing [
[SQL
SQL]
], push [
[Y
Y
Y
Y
YYY
Y
Y
Y
YY] ]or [
[Z
Z
Z
Z
ZZZ
Z
Z
Z
ZZ] ]to adjust noise
squelch level.
➥Push for 1 sec. to turn the monitor function ON.
➥While pushing [
[H/L
H/L ]
], push [
[SQL
SQL ](
]( L)
L) to toggle the
(microphone) Key lock function ON or OFF.
• “T” appears while Key lock function is in use.
•[[PWR
PWR ]
], [[PTT
PTT]
], [[VOL
VOL]
], [[SQL
SQL] ]and [[H/L
H/L] ]still function when
the (microphone) Key lock function is turned ON.
➥Advance the cursor while in channel comment program-
ming condition.
MONI
MONI
IC
DW
PWR SCAN H/L
TAG
DW
9
MONI
L
U/I/C
DIM
IC
SCR
CH/WX LO/DX
SQL
VOL
PA/RX
v
n
b,
.
⁄0
m
z x c
16
16
DIM
TAG
⁄0 VOLUME/DIMMER/PA/RX SPEAKER KEY
[VOL](
[VOL]( P
PA/RX
A/RX )
)
➥After pushing [[VOL
VOL]
], push [[Y
Y
Y
Y
YY
Y
Y
Y
Y
YY] ]or [[Z
Z
Z
Z
ZZ
Z
Z
Z
Z
ZZ] ]to adjust audio
level.
➥After pushing [VOL](
[VOL]( P
PA/RX
A/RX ) )for 1 sec, push [
[Y
Y
Y
Y
YY
Y
Y
Y
Y
YY] ]or
[[Z
Z
Z
Z
ZZ
Z
Z
Z
Z
ZZ] ]to adjust the brightness of the LCD and key backlight.
➥Move the cursor backward while in the channel comment
programming condition.
➥While pushing [H/L]
[H/L], push to turn the Hailer (Public Ad-
dress)* mode ON or OFF. (* Depends on the transceiver)
➥While pushing [H/L]
[H/L], push for 1 sec. to turn the RX
Speaker mode ON or OFF.
■Function display
qCHANNEL GROUP INDICATOR
Indicates whether an U.S.A. (USA), International (INT) or
Canadian (CAN) channel is selected.
wKEY LOCK INDICATOR
➥Appears while the Key lock function is in use.
➥ Blinks while the All key lock function is in use.
eCHANNEL NUMBER READOUT
➥Indicates the selected operating channel number. “A” ap-
pears when a simplex channel is selected. “b” appears
when a receive only channel for a Canadian channel group
is selected.
➥In Set mode, indicates the selected condition.
rVOLUME INDICATOR
Appears while audio output level is adjusted.
tSQUELCH INDICATOR
Appears while noise squelch level is adjusted.
yCHANNEL COMMENT INDICATOR
➥Channel comment appears (and scrolls) if programmed.
➥In Set mode, indicates or scrolls the selected Set mode item.
uATTENUATOR INDICATOR
Appears when the Attenuator function is in use.
iSCRAMBLER INDICATOR
Appears when an optional Voice scrambler* is activated.
* The Voice scrambler is available depends on the transceiver.
oSCAN INDICATOR
➥“SCAN” appears during Normal scan.
➥ “P SCAN” appears during Priority scan.
!0 PRIORITY CHANNEL INDICATOR
Indicates a priority channel during Priority scan or Dual/Tri-
watch.
!1 DUAL/TRI WATCH INDICATOR
“DUAL” appears during Dualwatch; “TRI” during Tri-watch.
!2 WEATHER CHANNEL INDICATOR
➥ “WX” appears when a weather channel is selected.
➥ “WX ALT” appears when the Weather alert function is in
use; blinks when an alert tone is received.
!3 LOW POWER INDICATOR
Appears when low power is selected.
!4 CALL CHANNEL INDICATOR
Appears when call channel is selected.
!5 DUPLEX INDICATOR
Appears when a duplex channel is selected.
!6 TAG CHANNEL INDICATOR
Appears when a TAG channel is selected.
!7 BUSY INDICATOR
Appears when receiving a signal or when the squelch opens.
!8 TRANSMIT INDICATOR
Appears while transmitting.
■Channel selection
D
D
D
D
DDChannel 16
qPush [
[] ]to select Channel 16.
wPush [
[CH/WXCH/WX] ]to return to the condition
before selecting Channel 16, or push [
[Y
Y
Y
Y
YY
Y
Y
Y
Y
YY]
]
or [
[Z
Z
Z
Z
ZZ
Z
Z
Z
Z
ZZ] ]to select an operating channel.
D
D
D
D
DDCall channel
qPush [
[](
]( 9
9) )for 1 sec. to select call
channel.
wPush [
[CH/WXCH/WX ] ]to return to the condition
before selecting call channel, or push [
[Y
Y
Y
Y
YY
Y
Y
Y
Y
YY]
]
or [
[Z
Z
Z
Z
ZZ
Z
Z
Z
Z
ZZ] ]to select an operating channel.
D
D
D
D
DDWeather channels
qPush [
[CH/WX
CH/WX ] ]once or twice to select
the weather channel group.
wPush [
[
Y
Y
Y
Y
YY
Y
Y
Y
Y
YY] ]or [
[Z
Z
Z
Z
ZZ
Z
Z
Z
Z
ZZ] ]to select a weather chan-
nel.
ePush [
[CH/WX
CH/WX ] ]to return to the condition
before selecting the weather channel
group.
D
D
D
D
DDU.S.A., International and Canadian channels
qPush [
[CH/WXCH/WX ](
]( U/I/C) U/I/C) to select a regular channel.
• Push [[CH/WXCH/WX ](]( U/I/C) U/I/C) again, if a weather channel appears.
wWhile pushing [
[H/L
H/L]
], push [
[CH/WX
CH/WX](
]( U/I/C)
U/I/C) to select a
channel group.
• U.S.A., International and Canadian channels can be selected in
sequence.
■Receiving and transmitting
qPush [
[PWR
PWR ]
]for 2 sec. to turn power ON.
wSet the audio and squelch levels.
➥Push [
[SQL
SQL]
], then push [
[Z
Z
Z
Z
ZZ
Z
Z
Z
Z
ZZ] ]until the noise appears.
➥Push [
[VOL
VOL]
], then push [
[Y
Y
Y
Y
YY
Y
Y
Y
Y
YY]
]/[
[Z
Z
Z
Z
ZZ
Z
Z
Z
Z
ZZ] ]to adjust the audio level.
➥Push [
[SQL
SQL]
], then push [
[Y
Y
Y
Y
YY
Y
Y
Y
Y
YY] ]until the noise disappears.
eTo change the channel group, push [
[CH/WXCH/WX](
]( U/I/C)
U/I/C)
while pushing [H/L].
rPush [
[Y
Y
Y
Y
YY
Y
Y
Y
Y
YY]
]or [
[Z
Z
Z
Z
ZZ
Z
Z
Z
Z
ZZ] ]to select the desired channel.
• When receiving a signal, “ ” appears and audio is emitted
from the speaker.
• Further adjustment of the audio level may be necessary.
• Use the optional Voice scrambler function for privacy.
tPush [
[LO/DXLO/DX]
]to turn the Attenuator function ON or OFF, if
necessary.
• “LOCAL” appears when the Attenuator function is in use.
yPush [
[H/LH/L ] ]to select the output power, if necessary.
• “LOW” appears when low power is selected.
• Choose low power for short range communications, choose high
power for longer distance communications.
• Some channels are for selecting low power only.
uPush and hold [
[PTT
PTT ]
]to transmit, then speak into the micro-
phone.
• “ ” appears.
• Channel 70 cannot be used for transmission other than DSC.
Simplex channels, 3, 21, 23, 61, 64, 81, 82 and 83 CANNOT
be lawfully used by the general public in U.S.A. waters.
iRelease [[PTT
PTT] ]to receive.
IMPORTANT: To maximize the readability of your transmitted
signal (voice), pause a few sec. after pushing [
[PTTPTT]
], hold the
microphone 2 to 4 inches (5 to 10 cm) from your mouth and
speak at a normal voice level.
DW
U.S.A. channels
Canadian channels
International channels
DW
DW
DW
16
16
1616
CALL
WX ALT
DUP
P SCAN
SCRM
LOCAL
TRI
DUAL
LOWTAG
CAN
USA
INT
L
TX BUSY
VOL
SQL
q
w
r
t
e
!8 !7 !4!5 !3
!2
!1
!0
o
i
u
y
!6
DIM
DIM
■HM-157 supplied accessories
Accessories included with the HM-157: Qty.
qConnection cable (OPC-1000: 6 m; 20 ft) ........................ 1
wMounting base .................................................................. 1
eMicrophone hanger .......................................................... 1
rScrews (M3 ×16; tapping) ............................................... 5
These instructions are described when the HM-157 is connected to the IC-M504. Some operations or indications may be dif-
ferent as these instructions depending on the connecting transceiver.
Icom, Icom Inc. and the logo are registered trademarks of Icom Incor-
porated (Japan) in the United States, the United Kingdom, Germany, France,
Spain, Russia and/or other countries. COMMANDMIC II is a trademark of
Icom Incorporated (Japan) in the United states.
q w e
r
Specyfikacje produktu
| Marka: | ICOM |
| Kategoria: | odbiornik |
| Model: | HM-157B |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z ICOM HM-157B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje odbiornik ICOM
5 Października 2024
5 Października 2024
5 Października 2024
29 Września 2024
28 Września 2024
27 Września 2024
26 Września 2024
22 Września 2024
20 Września 2024
20 Września 2024
Instrukcje odbiornik
- Rupert Neve Designs
- Skytronic
- Ferguson
- Sandberg
- Ground Zero
- Amplicom
- Soundstream
- Warm Audio
- Blustream
- Fontastic
- Polk
- GlobalSat
- Bugera
- AMS Neve
- Teufel
Najnowsze instrukcje dla odbiornik
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
30 Marca 2025