Instrukcja obsługi Kicker DX300 2
Kicker
Radia samochodowe
DX300 2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker DX300 2 (28 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 9 użytkowników na średnio 4.1 gwiazdek
Strona 1/28
DX AMPLIFIER
D
LIVIN’ LOUD
2011 DX Stereo Amps RevD.indd 1
2011 DX Stereo Amps RevD.indd 1
2011 DX Stereo Amps RevD.indd 1
2011 DX Stereo Amps RevD.indd 12011 DX Stereo Amps RevD.indd 1 11/3/2010 12:29:22 PM
11/3/2010 12:29:22 PM
11/3/2010 12:29:22 PM
11/3/2010 12:29:22 PM11/3/2010 12:29:22 PM
2
DX.2-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
battery’s negative post and the vehicle chassis is recommended.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: DX125.2 DX300.2
RMS Power
@ 14.4V, 4 stereo, 1% THD+NΩ
@ 14.4V, 2 stereo, 1% THD+NΩ
@ 14.4V, 4 mono, 1% THD+NΩ
30W x 2
60W x 2
125W x 1
75W x 2
150W x 2
300W x 1
Length, in. (cm) 8-1/4” (21) 12-1/4” (31)
Electronic Crossover 18dB/Octave High Pass Fixed
@ 100Hz, 18dB/Octave Low
Pass Fixed @ 80Hz
12dB/Octave, variable
50Hz-200Hz, selectable
HI, LO and OFF
Bass Boost Selectable 0/9dB @ 40Hz Variable 0–12dB @ 40Hz
Specifi cations common to all models:
Height, in. (mm) 2-1/4” (57)
Width, in. (mm) 8-5/16” (211)
Frequency Response ± 1dB 20Hz–20KHz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: DX125.2 / DX300.2
2011 DX Stereo Amps RevD.indd 2
2011 DX Stereo Amps RevD.indd 2
2011 DX Stereo Amps RevD.indd 2
2011 DX Stereo Amps RevD.indd 22011 DX Stereo Amps RevD.indd 2 11/3/2010 12:29:28 PM
11/3/2010 12:29:28 PM
11/3/2010 12:29:28 PM
11/3/2010 12:29:28 PM11/3/2010 12:29:28 PM
3
12V
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
DX125.2 1 x 40 Ampere 8 Gauge PK8, ZCK84
DX300.2 1 x 60 Ampere 8 Gauge PK8, ZCK84
The DX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER ZISL as shown (make sure you set the DX
amplifi er’s input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “LO”. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another amplifi er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
+
–
core conductor
battery
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
18”
(45cm)
24”
(60cm)
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. If you
ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the amplifi er--just the opposite as when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to amplifi er
2011 DX Stereo Amps RevD.indd 3
2011 DX Stereo Amps RevD.indd 3
2011 DX Stereo Amps RevD.indd 3
2011 DX Stereo Amps RevD.indd 32011 DX Stereo Amps RevD.indd 3 11/3/2010 12:29:28 PM
11/3/2010 12:29:28 PM
11/3/2010 12:29:28 PM
11/3/2010 12:29:28 PM11/3/2010 12:29:28 PM
Specyfikacje produktu
| Marka: | Kicker |
| Kategoria: | Radia samochodowe |
| Model: | DX300 2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kicker DX300 2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Radia samochodowe Kicker
4 Października 2024
1 Października 2024
29 Września 2024
25 Września 2024
24 Września 2024
24 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
Instrukcje Radia samochodowe
- Radia samochodowe Mystery
- Radia samochodowe Ground Zero
- Radia samochodowe Peiying
- Radia samochodowe Tokai
- Radia samochodowe Audison
- Radia samochodowe Nikkei
- Radia samochodowe Rockford Fosgate
- Radia samochodowe Twister
- Radia samochodowe Mini
- Radia samochodowe OneConcept
- Radia samochodowe Zenec
- Radia samochodowe Becker
- Radia samochodowe JVC
- Radia samochodowe Pure
- Radia samochodowe JBL
Najnowsze instrukcje dla Radia samochodowe
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
15 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
13 Stycznia 2025