Instrukcja obsługi Kicker IX500.2
Kicker
Radia samochodowe
IX500.2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker IX500.2 (28 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 4 użytkowników na średnio 3.5 gwiazdek
Strona 1/28
IX AMPLIFIER
IX500.2
English Version
Versión Español
Amplificador del la Serie IX.2
Deutsche Version
Stereoverstärker der IX.2-Serie
Version Francaise
Amplificateur de série IX.2
LIVIN’ LOUD
2010 IX 500.2 RevF.indd 1
2010 IX 500.2 RevF.indd 1
2010 IX 500.2 RevF.indd 1
2010 IX 500.2 RevF.indd 12010 IX 500.2 RevF.indd 1 11/5/2010 12:31:50 PM
11/5/2010 12:31:50 PM
11/5/2010 12:31:50 PM
11/5/2010 12:31:50 PM11/5/2010 12:31:50 PM
2IX AMPLIFIERS
IX.2-SERIES AMPLIFIERS Owner’s Manual
IX500.2
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er. Use the IXSM or IXSK
mounting kits (sold separately) to stack multiple IX amplifi ers.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Serial Number:
Model: IX500.2
RMS Power
@ 14.4V, 4 stereo, 1% THD+NΩ
@ 14.4V, 2 stereo, 1% THD+NΩ
@ 14.4V, 4 mono, 1% THD+NΩ
125W x 2
250W x 2
500W x 1
Length 9-3/8” (238mm)
Height 2-3/16” (55mm)
Width 7-7/8” (200mm)
Frequency Response ± 1dB 20Hz–20kHz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Electronic Crossover Selectable HI/LO/OFF, Variable 50–200Hz, 12dB/octave
Bass Boost Variable 0–18dB @ 40Hz
Maximum Effi ciency (2Ω) >80%
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
IXSK
sold separately
2010 IX 500.2 RevF.indd 2
2010 IX 500.2 RevF.indd 2
2010 IX 500.2 RevF.indd 2
2010 IX 500.2 RevF.indd 22010 IX 500.2 RevF.indd 2 11/5/2010 12:32:10 PM
11/5/2010 12:32:10 PM
11/5/2010 12:32:10 PM
11/5/2010 12:32:10 PM11/5/2010 12:32:10 PM
3
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
IX500.2 1 x 60 Ampere 4 Gauge PK4, CK4, ZCK4
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
battery’s negative post and the vehicle chassis is recommended.
The IX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER ZISL as shown below (make sure you set
the IX amplifi er’s input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-
level RCA outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “LO”. Either
input method will provide a low-level output signal at the RCA output, which effectively passes the audio signal
to another amplifi er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
+
–
core conductor
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. Install
a second fuse within 18” (45cm) of the amplifi er. If you ever need to remove the amplifi er from the vehicle after it
has been installed, the ground wire should be the last wire disconnected from the amplifi er--just the opposite as
when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to amplifi er
12V
18”
(45cm)
battery
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
24”
(60cm)
2010 IX 500.2 RevF.indd 3
2010 IX 500.2 RevF.indd 3
2010 IX 500.2 RevF.indd 3
2010 IX 500.2 RevF.indd 32010 IX 500.2 RevF.indd 3 11/5/2010 12:32:10 PM
11/5/2010 12:32:10 PM
11/5/2010 12:32:10 PM
11/5/2010 12:32:10 PM11/5/2010 12:32:10 PM
Specyfikacje produktu
| Marka: | Kicker |
| Kategoria: | Radia samochodowe |
| Model: | IX500.2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kicker IX500.2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Radia samochodowe Kicker
4 Października 2024
1 Października 2024
29 Września 2024
25 Września 2024
24 Września 2024
24 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
Instrukcje Radia samochodowe
- Radia samochodowe Shuttle
- Radia samochodowe Mtx Audio
- Radia samochodowe Brigmton
- Radia samochodowe Tevion
- Radia samochodowe SoundMAX
- Radia samochodowe Magnat
- Radia samochodowe Hifonics
- Radia samochodowe Fusion
- Radia samochodowe Audison
- Radia samochodowe Norauto
- Radia samochodowe Rockford Fosgate
- Radia samochodowe Adcom
- Radia samochodowe Raveland
- Radia samochodowe Pure
- Radia samochodowe Ford
Najnowsze instrukcje dla Radia samochodowe
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
15 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
13 Stycznia 2025