Instrukcja obsługi Kicker KMA360.4
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker KMA360.4 (13 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 7.5 użytkowników na średnio 4.3 gwiazdek
Strona 1/13
KMA150.2
KMA360.4
KMA600.4
KMA600.6
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE KMA
Benutzerhandbuch | Deutsch
MONOVERSTÄRKER DER KMA-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE KMA
KMA
AMPLIFIERS
Owner’s Manual
2
KMA MULTI-CHANNEL SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a dry, structurally sound location to mount your KICKER amplifi er. Make sure there
are no items behind the area where the screws will be driven. Choose a location that allows at least 4”
(10cm) of open ventilation for the amplifi er. Drill four holes using a 7/64” (3mm) bit and use the supplied
#8 screws to mount the amplifi er.
Wiring: The KMA amplifi er’s RCA inputs will receive either high or low level signals from your car stereo’s
source unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA input
on the end panel of the amplifi er using the KICKER KISL as shown (see page 3). Alternatively, the signal
can be delivered to the amplifi er using the low-level RCA outputs on the source unit. Keep the audio
signal cable away from factory wiring harnesses and other power wiring. If you need to cross this wiring,
cross it at a 90 degree angle.
PERFORMANCE
MODEL: KMA150.2 | KMA360.4 | KMA600.4 | KMA600.6
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN
A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM
TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR
COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN
VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM) CLEARANCE
BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.
Model: KMA150.2 KMA360.4 KMA600.4 KMA600.6
RMS Power
@ 14.4V, 4Ω stereo, ≤ 1% THD+N
@ 14.4V, 2Ω stereo, ≤ 1% THD+N
@ 14.4V, 4Ω bridged mono, ≤ 1% THD+N
40 x 2
75 x 2
150 x 1
65 x 4
90 x 4
180 x 2
75 x 4
150x 4
300 x 2
50 x 6
100 x 6
200 x 3
Length [in, cm] 8-1/16, 20.4 12-7/16, 31.5 12-7/16, 31.5 13-15/16, 35.3
Height [in, cm] 2-5/16, 5.9 2-5/16, 5.9 2-5/16, 5.9 2-5/16, 5.9
Width [in, cm] 6-11/16, 17 6-11/16, 17 6-11/16, 17 6-11/16, 17
Specifi cations common to all models:
Frequency Response ± 1dB 10Hz-20kHz
Signal-to-noise Ratio [dB]
1W Signal-to-noise Ratio [dB]
>95dB, A-weighted, re: rated power
-75dB
Input Sensitivity Low: 125mV-5V, High: 250mV-10V
Electronic Crossover Off, Variable HP & LP 50–200Hz, 12dB/octave slope150.2, 360.4, & 600.4:
600.6: Amps 1 & 2 - Variable HP 0–200Hz, 12dB/octave slope;
Amp 3 - Off, Variable HP & LP 50–200Hz. 12dB/octave slope
Subsonic fi lter fi xed @ 25Hz in LP mode
KickEQ™ Bass Boost 0–6dB @ 40Hz (600.6 AMP 3 only)
3
Install a fuse within 7” (18cm) of the battery and in-line with the power cable connected to your amplifi er.
source unit
high-level speaker
outputs
to amplifi er
shield
+
–
core conductor KICKER KISL (optional)
from source unit high-
level speaker outputs
OR
to amplifi er
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
KMA150.2 1 x 40 Ampere 8 Gauge KMPK8, PK8, CK8
KMA360.4 1 x 60 Ampere 8 Gauge KMPK8, PK8, CK8
KMA600.4 1 x 80 Ampere 4 Gauge KMPK4, PK4, CK4
KMA600.6 1 x 80 Ampere 4 Gauge KMPK4, PK4, CK4
12V
battery
external fuse
remote turn-on (see page 6)
POWER WIRING
ABYC-compliant power terminals
Amplifi er uses 304-stainless steel
screws and conformal coated PCB
for increased weather resistance
aluminum bottom
plate
≤7”
(18cm)
Specyfikacje produktu
| Marka: | Kicker |
| Kategoria: | odbiornik |
| Model: | KMA360.4 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kicker KMA360.4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje odbiornik Kicker
6 Października 2024
6 Października 2024
6 Października 2024
22 Września 2024
11 Września 2024
8 Września 2024
5 Września 2024
31 Sierpnia 2024
30 Sierpnia 2024
30 Sierpnia 2024
Instrukcje odbiornik
- odbiornik Sencor
- odbiornik Bresser
- odbiornik Skytronic
- odbiornik Markbass
- odbiornik Black Lion Audio
- odbiornik VMV
- odbiornik ATen
- odbiornik JB Systems
- odbiornik Graupner
- odbiornik Aguilar
- odbiornik Leema
- odbiornik JL Audio
- odbiornik Deaf Bonce
- odbiornik Sinus Live
- odbiornik Telestar
Najnowsze instrukcje dla odbiornik
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
30 Marca 2025