Instrukcja obsługi Kicker KXMA1500.1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker KXMA1500.1 (40 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 4.5 użytkowników na średnio 4.3 gwiazdek
Strona 1/40
KXMA1500.1
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE KXM
Benutzerhandbuch | Deutsch
STEREOVERSTÄRKER DER KXM-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE KXM
KXM
AMPLIFIERS
Owner’s Manual
2024 KXMA Mono Amp Rev F.indd 1
2024 KXMA Mono Amp Rev F.indd 1
2024 KXMA Mono Amp Rev F.indd 1
2024 KXMA Mono Amp Rev F.indd 1
2024 KXMA Mono Amp Rev F.indd 1 5/21/2024 11:18:18 AM
5/21/2024 11:18:18 AM
5/21/2024 11:18:18 AM
5/21/2024 11:18:18 AM
5/21/2024 11:18:18 AM
2
KXMA MONO-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no
items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm)
of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger
compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the
amplifi er.
Wiring: The KXMA amplifi er’s RCA inputs will receive either high or low level signals from your car stereo’s
source unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA
input on the end panel of the amplifi er using the KICKER KISL as shown. Alternatively, the signal can be
delivered to the amplifi er using the low-level RCA outputs on the source unit. Keep the audio signal cable
away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a
90 degree angle.
PERFORMANCE
MODEL: KXMA1500.1
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN
A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM
TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR
COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN
VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM) CLEARANCE
BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.
Model: KXMA1500.1
RMS Power
@ 14.4V, 4Ω mono, ≤ 1% THD+N
@ 14.4V, 2Ω mono, ≤ 1% THD+N
@ 14.4V, 1Ω mono, ≤ 1% THD+N
750W x 1
1500W x 1
1500W x 1
Length [in, cm] 11-3/16, 28.4
Height [in, cm] 2-1/8, 5.5
Width [in, cm] 8-5/16, 21
Frequency Response [Hz] 10Hz–160Hz
Signal-to-Noise Ratio [dB]
1W Signal-to-Noise Ratio [dB]
>95dB, A-weighted, re: rated power
-75dB
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Subsonic Filter 10Hz–80Hz, 24dB/octave (BW)
Selectable Electronic Crossover Variable LP 40–160Hz, 24dB/octave (BW)
KickEQ+™ Bass Boost 0–6dB @ 20Hz–80Hz
Remote Bass Yes (Included)
2024 KXMA Mono Amp Rev F.indd 2
2024 KXMA Mono Amp Rev F.indd 2
2024 KXMA Mono Amp Rev F.indd 2
2024 KXMA Mono Amp Rev F.indd 2
2024 KXMA Mono Amp Rev F.indd 2 5/21/2024 11:18:23 AM
5/21/2024 11:18:23 AM
5/21/2024 11:18:23 AM
5/21/2024 11:18:23 AM
5/21/2024 11:18:23 AM
3
Install a fuse within 7” (18cm) of the battery and in-line with the power cable connected to your amplifi er.
Use only KICKER KMPK Wiring Kits or other genuine KICKER marine accessories when installing
amplifi ers in marine applications.
POWER WIRING
source unit
high-level speaker
outputs
to amplifi er
shield
+
–
core conductor KICKER KISL (optional)
from source unit high-
level speaker outputs
OR
to amplifi er
Model External Fuse Power/Ground Wire(sold separately)
KXMA1500.1 1 x 150 Ampere 1/0 Gauge
+
POWER
GND 12V INPUT OUTPUT
SPEAKER
REM AUTO
TURN-ON
L
R
INPUT LEVEL
12V/DC/AUDIO
REMOTE BASS
LOW/HI/
-
12V
battery
external fuse
remote turn-on (see page 7)
≤7”
(18cm)
ABYC-compliant power terminals Amplifi er uses 304-stainless steel screws
and conformal coated PCB for increased
weather resistance
aluminum bottom plate
2024 KXMA Mono Amp Rev F.indd 3
2024 KXMA Mono Amp Rev F.indd 3
2024 KXMA Mono Amp Rev F.indd 3
2024 KXMA Mono Amp Rev F.indd 3
2024 KXMA Mono Amp Rev F.indd 3 5/21/2024 11:18:23 AM
5/21/2024 11:18:23 AM
5/21/2024 11:18:23 AM
5/21/2024 11:18:23 AM
5/21/2024 11:18:23 AM
Specyfikacje produktu
| Marka: | Kicker |
| Kategoria: | odbiornik |
| Model: | KXMA1500.1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kicker KXMA1500.1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje odbiornik Kicker
6 Października 2024
6 Października 2024
6 Października 2024
22 Września 2024
11 Września 2024
8 Września 2024
5 Września 2024
31 Sierpnia 2024
30 Sierpnia 2024
30 Sierpnia 2024
Instrukcje odbiornik
- odbiornik Humax
- odbiornik SureCall
- odbiornik MEE Audio
- odbiornik Cambridge
- odbiornik CE Labs
- odbiornik SIIG
- odbiornik Memphis Audio
- odbiornik Konig
- odbiornik Hirschmann
- odbiornik Yamaha
- odbiornik Pioneer
- odbiornik Roswell
- odbiornik Velleman
- odbiornik Audison
- odbiornik Audix
Najnowsze instrukcje dla odbiornik
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
30 Marca 2025