Instrukcja obsługi Kicker KXMA500.4
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker KXMA500.4 (14 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 5.5 użytkowników na średnio 4.1 gwiazdek
Strona 1/14
KXMA400.2 | KXMA1200.2
KXMA500.4 | KXMA800.4
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE KXM
Benutzerhandbuch | Deutsch
STEREOVERSTÄRKER DER KXM-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE KXM
KXM
AMPLIFIERS
Owner’s Manual
2
KXMA STEREO-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no
items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm)
of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger
compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the
amplifi er.
Wiring: The KXMA amplifi er’s RCA inputs will receive either high or low level signals from your car stereo’s
source unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA
input on the end panel of the amplifi er using the KICKER KISL as shown. Alternatively, the signal can be
delivered to the amplifi er using the low-level RCA outputs on the source unit. Keep the audio signal cable
away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a
90 degree angle.
PERFORMANCE
MODEL: KXMA400.2 | KXMA1200.2 | KXMA500.4 | KXMA800.4
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN
A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM
TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR
COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN
VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM) CLEARANCE
BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.
Model: KXMA400.2 KXMA1200.2 KXMA500.4 KXMA800.4
RMS Power
@ 14.4V, 4 stereo, ≤ 1% THD+N
@ 14.4V, 2 stereo, ≤ 1% THD+N
@ 14.4V, 4Ω bridged mono, ≤ 1% THD+N
100 x 2
200 x 2
400 x 1
300 x 2
600 x 2
N/A
75 x 4
125 x 4
250 x 2
100 x 4
200 x 4
400 x 2
Length [in, cm] 9-9/16, 24.4 11-3/16, 28.4 11-3/16, 28.4 11 9/16, 29.4
Specifi cations common to all models:
Height [in, cm] 2-1/8, 5.5
Width [in, cm] 8-5/16, 21
Frequency Response [Hz] 10Hz–20kHz
Signal-to-Noise Ratio [dB]
1W Signal-to-Noise Ratio [dB]
95dB
-75dB
95dB
-70dB
95dB
-75dB
95dB
-75dB
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Selectable Electronic Crossover 800.4 and 500.4
AMP1: OFF, Variable HP 10–5000Hz with 10X switch, Variable LP 10–5000Hz
with 10X switch
AMP2: OFF, Variable HP 10–500Hz, Variable LP 40–5000Hz with 10X switch
(Bandpass capable); Slope: 24dB/octave
400.2 and 1200.2
OFF, Variable HP 10–500Hz; Variable LP 40–5000Hz with 10X Switch
(Bandpass capable); Slope: 24dB/octave
KickEQ™ Bass Boost 0–6dB @ 40Hz
3
Install a fuse within 7” (18cm) of the battery and in-line with the power cable connected to your amplifi er.
POWER WIRING
source unit
high-level speaker
outputs
to amplifi er
shield
+
–
core conductor
KICKER KISL (optional)
from source unit high-
level speaker outputs
OR
to amplifi er
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
KXMA400.2 1 x 60 Ampere 8 Gauge KMPK8, PK8, CK8
KXMA1200.2 1 x 150 Ampere 1/0 Gauge PKD1
KXMA500.4 1 x 60 Ampere 4 Gauge KMPK4, PK4, CK4
KXMA800.4 1 x 100 Ampere 4 Gauge KMPK4, PK4, CK4
INPUT
LEVEL
LO/HI
12V
battery
external fuse
remote turn-on (see page 6)
≤7”
(18cm)
ABYC-compliant power terminals
Amplifi er uses 304-stainless steel screws
and conformal coated PCB for increased
weather resistance
aluminum bottom plate
Specyfikacje produktu
| Marka: | Kicker |
| Kategoria: | odbiornik |
| Model: | KXMA500.4 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kicker KXMA500.4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje odbiornik Kicker
6 Października 2024
6 Października 2024
6 Października 2024
22 Września 2024
11 Września 2024
8 Września 2024
5 Września 2024
31 Sierpnia 2024
30 Sierpnia 2024
30 Sierpnia 2024
Instrukcje odbiornik
- odbiornik Cranborne Audio
- odbiornik Apart
- odbiornik Integra
- odbiornik Aeon Labs
- odbiornik QTX
- odbiornik Madison
- odbiornik Harman Kardon
- odbiornik Arcam
- odbiornik Matrox
- odbiornik Dual
- odbiornik Konig
- odbiornik Revel
- odbiornik Cloud
- odbiornik FiiO
- odbiornik CYP
Najnowsze instrukcje dla odbiornik
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
30 Marca 2025