Instrukcja obsługi Kicker zx 1000 1
Kicker
Radia samochodowe
zx 1000 1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker zx 1000 1 (28 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 20 osób i została oceniona przez 10.5 użytkowników na średnio 4.9 gwiazdek
Strona 1/28
ZX AMPLIFIER
ZX1000.1
ZX1500.1
ZX2500.1
English Version
Versión Español
Amplificador del la Serie ZX.1
Deutsche Version
Stereoverstärker der ZX.1-Serie
Version Francaise
Amplificateur de série ZX.1
LIVIN’ LOUD
2011 ZX 1000.1 1500.1 2500.1 RevA.indd 12011 ZX 1000.1 1500.1 2500.1 RevA.indd 1 10/4/2010 4:25:53 PM10/4/2010 4:25:53 PM
2ZX AMPLIFIERS
ZX.1-SERIES AMPLIFIERS Owner’s Manual
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
battery’s negative post and the vehicle chassis is recommended.
The ZX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER ZISL as shown (make sure you set the ZX
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: ZX1000.1 ZX1500.1 ZX2500.1
RMS Power
@ 14.4V, 4Ω mono, 1% THD+N
@ 14.4V, 2Ω mono, 1.5% THD+N
500W x 1
1000W x 1
750W x 1
1500W x 1
1250W x 1
2500W x 1
Length 16-3/4” (425mm) 20” (507mm) 27-1/2 (697mm)
Specifi cations common to all models:
Height 2-1/8” (54mm)
Width 9-5/8” (244mm)
Frequency Response ± 1dB 25Hz–200Hz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Selectable Electronic Crossover Variable lo-pass 50–200Hz, 24dB/octave
Bass Boost Variable 0–18dB @ 40Hz
Subsonic Filter 24dB/octave, fi xed @ 25Hz
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: ZX1000.1 / ZX1500.1 / ZX2500.1
2011 ZX 1000.1 1500.1 2500.1 RevA.indd 22011 ZX 1000.1 1500.1 2500.1 RevA.indd 2 10/4/2010 4:25:59 PM10/4/2010 4:25:59 PM
3
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
ZX1000.1 1 x 100 Ampere 1/0 Gauge PKD1, PK4, CK44, ZCK44
ZX1500.1 1 x 150 Ampere 1/0 Gauge PKD1, PK4, CK44, ZCK44
ZX2500.1 1 x 300 Ampere 1/0 Gauge PKD1, PK4, CK44, ZCK44
amplifi er’s input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “LO”. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another amplifi er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
+
–
core conductor
GND REM +12V
12V
battery
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
18”
(45cm)
24”
(60cm)
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. If you
ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the amplifi er--just the opposite as when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to amplifi er
protection LED
2011 ZX 1000.1 1500.1 2500.1 RevA.indd 32011 ZX 1000.1 1500.1 2500.1 RevA.indd 3 10/4/2010 4:25:59 PM10/4/2010 4:25:59 PM
Specyfikacje produktu
| Marka: | Kicker |
| Kategoria: | Radia samochodowe |
| Model: | zx 1000 1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kicker zx 1000 1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Radia samochodowe Kicker
4 Października 2024
1 Października 2024
29 Września 2024
25 Września 2024
24 Września 2024
24 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
Instrukcje Radia samochodowe
- Radia samochodowe Roadstar
- Radia samochodowe MB Quart
- Radia samochodowe Dension
- Radia samochodowe Hifonics
- Radia samochodowe Crunch
- Radia samochodowe Sony
- Radia samochodowe Skoda
- Radia samochodowe Caliber
- Radia samochodowe Spectron
- Radia samochodowe Scion
- Radia samochodowe Audiovox
- Radia samochodowe Medion
- Radia samochodowe Conceptronic
- Radia samochodowe VDO
- Radia samochodowe DLS
Najnowsze instrukcje dla Radia samochodowe
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
15 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
13 Stycznia 2025