Instrukcja obsługi Kicker ZX350.4
Kicker
Radia samochodowe
ZX350.4
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker ZX350.4 (28 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 5 użytkowników na średnio 4.4 gwiazdek
Strona 1/28
ZX AMPLIFIER
ZX350.4
ZX650.4
English Version
Versión Español
Amplificador del la Serie ZX.4
Deutsche Version
Stereoverstärker der ZX.4-Serie
Version Francaise
Amplificateur de série ZX.4
LIVIN’ LOUD
2011 ZX 350.4 650.4 RevC.indd 1
2011 ZX 350.4 650.4 RevC.indd 1
2011 ZX 350.4 650.4 RevC.indd 1
2011 ZX 350.4 650.4 RevC.indd 12011 ZX 350.4 650.4 RevC.indd 1 11/5/2010 1:13:34 PM
11/5/2010 1:13:34 PM
11/5/2010 1:13:34 PM
11/5/2010 1:13:34 PM11/5/2010 1:13:34 PM
2ZX AMPLIFIERS
ZX.4-SERIES AMPLIFIERS Owner’s Manual
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
battery’s negative post and the vehicle chassis is recommended.
The ZX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER ZISL as shown (make sure you set the ZX
amplifi er’s input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “LO”. Keep the
audio signal cable away from factory wiring harnesses and other power wiring. If you need to cross this wiring,
cross it at a 90 degree angle.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: ZX350.4 ZX650.4
RMS Power, all channels driven
@ 14.4V, 4 stereo, 1% THD+NΩ
@ 14.4V, 2 stereo, 1% THD+NΩ
@ 14.4V, 4 mono, 1% THD+NΩ
60W x 4
90W x 4
175W x 2
120W x 4
160W x 4
325W x 2
Length 13-1/2” (342mm) 20” (507mm)
Specifi cations common to all models:
Height 2-1/8” (54mm)
Width 9-5/8” (244mm)
Frequency Response ± 1dB 20Hz–20kHz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Selectable Electronic Crossover Variable HI, LO, or OFF (bypass) | 50–200Hz, 12dB/octave
Bass Boost Variable 0–18dB @ 40Hz
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: ZX350.4 / ZX650.4
2011 ZX 350.4 650.4 RevC.indd 2
2011 ZX 350.4 650.4 RevC.indd 2
2011 ZX 350.4 650.4 RevC.indd 2
2011 ZX 350.4 650.4 RevC.indd 22011 ZX 350.4 650.4 RevC.indd 2 11/5/2010 1:13:53 PM
11/5/2010 1:13:53 PM
11/5/2010 1:13:53 PM
11/5/2010 1:13:53 PM11/5/2010 1:13:53 PM
3
Model External Fuse Power/Ground Wire KICKER Wiring Kit
ZX350.4 1 x 60 Ampere 8 Gauge PK8, CK8, ZCK8
ZX650.4 1 x 100 Ampere 4 Gauge PK4, CK4, ZCK4
source unit
high-level speaker
outputs
to amplifi er
shield
+
–
core conductor
GND REM +12V
12V
battery
external fuse
protection LED
remote turn-on
(see page 5)
bare-metal
chassis ground
18”
(45cm)
24”
(60cm)
AMP1
AMP1
L+ L- R+ R-
AMP2
L+ L- R+ R-
L+ BRIDGE WIRING R-
AMP2
L LR R
L+ L- R+ R- L+ L- R+ R-
signal in
FOUR CHANNEL OPERATION
minimum impedance of 2 ohms per channel
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. If you
ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the amplifi er--just the opposite as when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to amplifi er
2011 ZX 350.4 650.4 RevC.indd 3
2011 ZX 350.4 650.4 RevC.indd 3
2011 ZX 350.4 650.4 RevC.indd 3
2011 ZX 350.4 650.4 RevC.indd 32011 ZX 350.4 650.4 RevC.indd 3 11/5/2010 1:13:54 PM
11/5/2010 1:13:54 PM
11/5/2010 1:13:54 PM
11/5/2010 1:13:54 PM11/5/2010 1:13:54 PM
Specyfikacje produktu
| Marka: | Kicker |
| Kategoria: | Radia samochodowe |
| Model: | ZX350.4 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kicker ZX350.4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Radia samochodowe Kicker
4 Października 2024
1 Października 2024
29 Września 2024
25 Września 2024
24 Września 2024
24 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
Instrukcje Radia samochodowe
- Radia samochodowe Ford
- Radia samochodowe Autovision
- Radia samochodowe Scion
- Radia samochodowe Maginon
- Radia samochodowe Nedis
- Radia samochodowe Nikkei
- Radia samochodowe Sendai
- Radia samochodowe RTO
- Radia samochodowe Manta
- Radia samochodowe Boston Acoustics
- Radia samochodowe Tokai
- Radia samochodowe Mac Audio
- Radia samochodowe Hyundai
- Radia samochodowe Denver
- Radia samochodowe Kenwood
Najnowsze instrukcje dla Radia samochodowe
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
15 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
13 Stycznia 2025