Instrukcja obsługi Lenco IR-3000

Lenco radio IR-3000

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lenco IR-3000 (1 stron) w kategorii radio. Ta instrukcja była pomocna dla 47 osób i została oceniona przez 24 użytkowników na średnio 4.6 gwiazdek

Pobierz PDF

Strona 1/1

If you choose to configure the network, then proceed as

follows:

1 press “Tune/Select” to select “Configure”,

press “Tune/Select”

2 press “Tune/Select” to select “Network Config ”, press

“Tune/Select”

3 press “Tune/Select” to select “Wired/ ”, Wireless

then press “Tune/Select”

4 press “Tune/Select” to select “Auto Wired Only”, “ ” or

“ Wireless Only”. If you only use Wired or Wireless(Wi-

Fi) you can select “Auto” (default), if you have both

connected then you should select the connection you

want to use.

Please refer to the manual for a more detailed explanation

about the internet radio’s functions and features.

When you have a wired connection then the installation is

finished, if you have a wireless connection (Wi-Fi) then

proceed as follows:

1 press “Tune/Select” to select “Wireless Only”, then

press “select”

NOTE: We select “Wireless Only” here because p1-we want to

make sure the device will search for an access point. Once

everything is configured you can choose to set back the

system connection to “auto”.

2 press “Tune/Select” to select “Scan for network”, then

press “Tune/Select”, the device will search for the

available access point.

3 once an access point is found press “Tune/Select”

4 when the network needs no WEP or WPA code, the

display will show as follows:

5 if the network needs a WEP or WPA code, then the

device enters the code entry mode after three seconds:

Network OK

6 press “Tune/Select” to select each character of the

code, press “Tune/Select” to confirm the character.

NOTE: WEP and WPA codes are case sensitive to upper

and lower case characters.

7 after the final character, press “Tune/Select” to select

“ ”, press “Tune/Select” to confirm END

8 the device will now try to connect to the network:

9 After the connection is made and the code is

accepted, the display will show:

Network OK

Interne

Radio

1 press “Mode” to switch to Internet radio mode

2 the device will connect to the network and show the

following screen:

3 press “Tune/Select” to select “

Stations

”,

press “Tune/Select”

4 press “Tune/Select” to select “Location” or

“ ”, press “Tune/Select” Genre

5 press “Tune/Select” to select a specific location or a

specific genre, press “Tune/Select” to confirm your

item of choice, the display will now show the number

of stations that are loading.

6 press “Tune/Select” to select the station of your

choice, press select, the station will be loaded

7 press the” preset” button. The following will show on

the LCD display:

Stations

Configure

Preset 1

< Preset 2 >

8 Turn the dial until Preset 1 is showing.

9 Hold the “Select” button for about 3 seconds, until the

screen displays:

Assigned to Preset 1

Preparation / installation:

Connect the AC Cord into the socket on the back.

Connect an ethernet-RJ45-network-cable into the RJ45

socket on the back of the unit if you use Wired Ethernet.

Make sure this cable is also connected to the network that

provides the internet connection.

During the first startup, the display will show the following

screens:

QUICK-GUIDE IR-3000

Reciva Enabled

ARM Powered

Initializing

Network

Connecting to

Network

< {} ~ END < > 0

Connecting to

Network

Specyfikacje produktu

Marka:	Lenco
Kategoria:	radio
Model:	IR-3000
Kolor produktu:	Srebrny
Typ wyświetlacza:	LCD
Waga produktu:	2000 g
W zestawie pilot zdalnego sterowania:	Tak
Technologia łączności:	Bezprzewodowy
Wbudowane głośniki:	Nie
Pobór mocy w trybie czuwania:	1.8 W
Zakresy tunera:	FM
Pobór mocy:	8 W
Wymiary produktu (SxGxW):	430 x 310 x 60 mm
Zasilanie:	AC 230 V
Obsługiwane nośniki:	mp3, WMA, RA, aac, ogg
Zintegrowany zegar:	Tak
Radio:	Przenośny
Wyłącznik czasowy:	Tak
Typ tunera:	Cyfrowy
Obudowa kasety:	Nie