Instrukcja obsługi Luxul XAP-1510
Luxul
Punkt dostępu
XAP-1510
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Luxul XAP-1510 (2 stron) w kategorii Punkt dostępu. Ta instrukcja była pomocna dla 30 osób i została oceniona przez 15.5 użytkowników na średnio 4.9 gwiazdek
Strona 1/2
READ ME FIRST
QUICK INSTALL GUIDE
High Power AC1900
Dual-Band Wireless Access Point
XAP-1510
Includes:
One: High Power AC1900 Dual-Band Wireless AP
Two: Mounting Brackets and Hardware
One: PoE Injector and Power Adapter
One: Ethernet Cables
READ ME FIRST - CONTROLLER COMPATIBILITY
This XAP-1510 is compatible with the Luxul Wireless Controller for fast, easy
confi guration and deployment of wireless networks with multiple APs.
nNote: If you’ll be using this AP with a Wireless Controller, refer to
the Quick Install Guide included with the Wireless Controller for
setup instructions.
AP SETUP AND CONFIGURATION
1 Physical Installation
The XAP-1510 access point is designed for simple and effi cient installation
and can be located one of three ways. First, the included mount is designed to
attach directly to several different regions’ standard electrical boxes. Second,
the XAP-1510 may be mounted on a ceiling or wall without a box by using the
included mount as a guide to mark attachment locations. Finally, the XAP-1510
can be placed on a fl at surface by attaching the included rubber feet
to the mount.
cCaution: Attach the rubber feet to the mount and attach the mount to
the AP for fl at surface placement to avoid overheating and failure.
uSingle Access Point Placement: Because the signal generated by the
XAP-1500 is omnidirectional, the unit should be located as near as possible
to the center of the desired coverage area.
XAP-1510 Single AP Coverage Pattern
uMultiple Access Point Placement: You may need to experiment with
AP placement to optimize the roaming experience. Place APs to ensure
adequate coverage, but not so far apart that there is no signal overlap.
Adjacent APs should overlap enough that the client device has a good
connection to the AP to which it is currently attached, but also sees the
next-nearest AP. Ideally, roaming clients should see signal strength of
two overlapping APs in the range of -60 to -70 dBm at the midway
point between two APs. To learn more about AP placement, visit
luxul.com/ap-placement.
Ideally, roaming clients should see
signal strength of two overlapping
APs in the range of -60 to -70 dBm at
the midway point between two APs
XAP-1510 Multiple AP Coverage and Overlap
nNote: Consider using Ekahau HeatMapper to assist with this process,
available from www.ekahau.com. Luxul also offers an informative
“How-To” video on HeatMapper at luxul.com/how-to-videos.
AP SETUP AND CONFIGURATION CONT.
2 Connecting Ethernet and Power
Ethernet and Power
To apply power and network simultaneously, simply connect one end of an
Ethernet cable to a PoE switch, and the other end to the XAP-1510 PoE port.
To connect power and Ethernet separately, fi rst connect an Ethernet cable
from the supplied PoE Injector Data & PWR Out port to the PoE port on
the XAP-1510. An Ethernet cable length of up to 300 feet can be used.
LEGAL AND REGULATORY INFORMATION
No part of this publication, or any other publication may be modifi ed or adapt-
ed in any way, for any purposes without permission in writing from Luxul. The
material in this manual is subject to change without notice. Luxul reserves the
right to make changes to any product to improve reliability, function, or design.
No license is granted, either expressly or by implication or otherwise under any
Luxul intellectual property rights. An implied license only exists for equipment,
circuits and subsystems contained in this or any Luxul product.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
FCC ID: W59XAP1510
IC: 8584A-XAP1510
FCC Statement—Wireless FCC 2.4GHz & 5GHz 802.11abgn
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020,
declares that this Luxul XAP-1510 is in compliance with the essential
requirements and other relevant provisions of Directive 1995/5/EC.
For a copy of this report send a self addressed stamped envelope
to: Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.
Industry Canada (RSS-Gen Issue 4)
CAN ICES-3(B)/NMB-3(B)
Sales
P: 801-822-5450
E: sales@luxul.com
Technical Support
P: 801-822-5450 Option 3
E: support@luxul.com
© 2015 Luxul. All Rights Reserved. LUX-QIG-XAP-1510-v3 07271511
Specyfikacje produktu
| Marka: | Luxul |
| Kategoria: | Punkt dostępu |
| Model: | XAP-1510 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Luxul XAP-1510, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Punkt dostępu Luxul
14 Stycznia 2025
14 Stycznia 2025
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
Instrukcje Punkt dostępu
- HP
- Mach Power
- Moog
- NUVO
- Allied Telesis
- Interlogix
- Dahua Technology
- Amped Wireless
- Meru
- CradlePoint
- AVM
- Draytek
- Netgear
- Asus
- Black Box
Najnowsze instrukcje dla Punkt dostępu
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
2 Kwietnia 2025
20 Marca 2025
28 Lutego 2025
27 Stycznia 2025
26 Stycznia 2025
15 Stycznia 2025
12 Stycznia 2025