Instrukcja obsługi Milwaukee 48-22-9419
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Milwaukee 48-22-9419 (1 stron) w kategorii Hamer. Ta instrukcja była pomocna dla 20 osób i została oceniona przez 10.5 użytkowników na średnio 3.7 gwiazdek
Strona 1/1
54-49-9419
SERVICE PARTS LIST
BULLETIN NO.
MILWAUKEE TOOL l www.milwaukeetool.com
13135 W. LISBON RD., BROOKFIELD, WI 53005
Drwg. 1
EXAMPLE:
Component Parts (Small #) Are Included
When Ordering The Assembly (Large #).
0
00
48-22-9419 Milled Face Hickory Hammer
48-22-9519 Smooth Face Hickory Hammer
HICKORY HAMMERS July 2018
REVISED BULLETIN
WIRING INSTRUCTION
DATE
CAT. NO.
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 -------------- Steel Wedge (2)
2 -------------- Wood Wedge (1)
3 -------------- Hammer Head
(Milled: 48-22-9419, Smooth: 48-22-9519)
(1)
4 -------------- Hickory Hammer Handle (1)
5 14-46-9419 Handle Replacement Kit (1)
1
2
3
4
5 1 2
4
1. Before beginning, line up the wooden wedge with the slot in the top of
the replacement handle. With a pencil, make a mark on the thick side
of the wooden wedge where the top of the handle ends. This will allow
you to see when the wooden wedge is fully inserted down into the
handle slot. It is important not to exceed the slot depth with the wedge,
as this can cause damage to the new handle.
2. Aftercuttingtheoldhandleobelowthehead,turntheheadoverand
punch the remaining handle material out from the top of the 'eye' of
the hammer head. Insert slotted end of the new replacement handle
into the bottom of the hammer head. Firmly tap the bottom of handle
with a mallet or other hammer to tightly set the handle into eye of the
head, but not so far as to 'peel' or cut into the wood of the handle at
the bottom of the eye. Rely on the mechanical bond of the wood and
steel wedges to make the head-to-handle connection strong.
3. Next place the thin tip of the wooden wedge into the slotted end of the
handle that is protruding out of the top of the hammer head. It is norm-
al for the wooden wedge to be wider than the slot and eye opening.
Firmly tap the wooden wedge all the way to the pencil mark on wedge,
so that the wedge is fully inserted in the handle slot. There should be
approximately 1/2" of the wedge protruding past the end of the handle.
DONOTcontinuedrivingthewedgeinanyfurther.
MILWAUKEE Hickory Replacement Instructions
USE CAUTION and Wear safety glasses when performing the following procedure.
4. Afterdrivingthewoodenwedgein,trimoexcesswedgeandhandle
material as close to the top of the head as possible. USE CAUTION
whencuttingoexcessmaterial.Positionthetwosteelwedgeson
trimmed end of handle and wood wedge to get an idea of spacing.
Position the larger steel wedge to the wider front of the eye, and the
smallersteelwedgetothebackoftheeye.Whenyouhavewedges
evenlyspacedintheeye,notincontactwiththesideoftheeye,rmly
tapthewedgesin,oneatatimecompletelyushwiththetrimmed
surface.
5. To keep the cut end of the handle from losing moisture and shrinking
inside the hammer head, put a few drops of mineral or 'butcherblock'
oil on the end grain to help retain the moisture content. This will pro-
longtheservicelifeofthehandle.
Model 48-22-9419
Shown with milled face
Pencil
mark
Bottom
of slot
1
Specyfikacje produktu
| Marka: | Milwaukee |
| Kategoria: | Hamer |
| Model: | 48-22-9419 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Milwaukee 48-22-9419, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Hamer Milwaukee
13 Stycznia 2025
4 Października 2024
2 Października 2024
21 Września 2024
16 Września 2024
8 Września 2024
7 Września 2024
4 Września 2024
2 Września 2024
1 Września 2024
Instrukcje Hamer
- Prowork
- DeWalt
- Power Craft
- Bosch
- Black & Decker
- Bavaria By Einhell
- Einhell Bavaria
- Hitachi
- Taurus
- King Craft
- XU1
- Ferm
- Bavaria
- Ergotools Pattfield
- RYOBI
Najnowsze instrukcje dla Hamer
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
29 Marca 2025
29 Marca 2025
29 Marca 2025
29 Marca 2025
29 Marca 2025
26 Marca 2025