Instrukcja obsługi Muse M-090 MR

Muse Radia samochodowe M-090 MR

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Muse M-090 MR (2 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 5.5 użytkowników na średnio 4.4 gwiazdek

Pobierz PDF

Strona 1/2

1. Do not attempt to modify the unit, modifying the unit may cause an accident.

2. Installation or servicing of the unit by persons without training and experience

in electronic equipment and automotive accessories may be dangerous and

could expose you to the risk of electric shock or other hazards.

3. Stop the vehicle before carrying out any operation that could interfere with

your driving.

4. Keep the volume at a level which you could hear sounds from outside the

vehicle.

5. Do not work in extremely high or low temperature. Be sure the temperature

inside the vehicle is between +60°C and -10°C before turning on your unit.

6. When replacing the fuse(s), the replacement must be of the same amperage

as shown on the fuse holder.

7. Do not block vents or radiator panels. Blocking them will cause heat to build up

inside and may result in re.

8. Using this unit without running the engine can result in battery drainage.

9. Use only in cars with a 12 volt negative ground.

10. After completing the installation or replacing the car battery you need to

RESET the unit before using it. Remove the front panel and press button RESET

on the base with pointed object (such as ball-point pen) to reset the unit to its

initial settings.

M-090 MR

GB - 1

User Manual

CAR RADIO WITH USB & SD

Please read the instruction carefully

before operating the unit.

PRECAUTIONS

English GB - 2 GB - 3

CONNECTION

Caution!

- Make sure to connect the color coded leads according to the diagram. Incorrect

connections may cause the unit to malfunction or damage the vehicle’s electrical

system.

- Make sure to connect the speaker (-) leads to the speaker (-) terminal. Never

connect the left and right channel speaker cables each other or to the vehicle body.

- Make sure all the connections are completely correct before turning on your unit.

- Before wiring, disconnect the cable from the negative battery terminal.

Do not connect the ignition wire (red) and the battery wire (yellow), it may

cause a short circuit, even result in re.

GB - 4 GB - 5 GB - 6

UNPACK YOUR UNIT

When you unpack your new car radio, make sure that you have removed all the

accessories and information papers:

Main unit

User manual

Accessories:

Install the unit

- Method 1: DIN Front - Mount

INSTALL AND REMOVE THE UNIT

GB - 7

MODE

BA ND

AUX IN

DIR-/8

RESET

SD/MMC

AS/ PS

DIR+/9

PTY/0

SEL/VOL /AF /TA

Reset

5.5

1. Insert the mounting sleeve to the car. Bend the claws outward for a tight t, if

necessary.

M5 x 25 Screw

2. Combine mounting blot, steel bar, spring washer and Hex nut. Then combine

the unit and dashboard with M5x 25 screw and plain washer.

- Method 2 DIN Rear-mount (For Japanese car)

1. Select a position where the screw holes of the mounting bracket supplied with

the car and the screw holes of the main unit become aligned (are tted).

M5X5.5 Screw

2. Tighten the screws. And then fasten them to the car.

Detach the Unit

Insert the keys supplied on the both sides of the unit (shown as illustrated)

until they click. Pulling the keys and makes them to remove the unit from the

dashboard.

LOCATION OF CONTROLS

MOD E

BA ND

AUX IN

DIR -/8

RESET

SD/MM C

AS /PS

DIR +/9

PTY/0

SEL/VOL/ AF /TA

1 2 3 4 5 6 7 17

16 15 14 13 12 11 10 18 9 8

1. button7/MODE

2. button0/BAND/PTY

3. numeric button1

4. button (Skip backward /Directory down)8/ /DIR-

5. /SEL/VOL/ AF/TA knob (Power/ Select setting/Volume)

6. numeric button4

7. LCD display

8. AUX IN jack

9. USB port

10. numeric button6

11. numeric button5

12. button (Skip forward /Directory up)9/ /DIR+

13. numeric button2

14. numeric button3

15. buttonAS/PS

16. / button (Play/ Pause/Random)RDM

17. SD/MMC card slot

18. button RESET

BASIC OPERATIONS

Turn on/off the unit

Press button (5) to turn on the unit. Press and hold this button again to turn off

the unit.

To display and adjust the current time

In standby mode, the current time will be displayed automatically.

Turn on the unit, press and hold button (1) until clock time appears. Long MODE

press /MODE button (1) again ,the hour digits will ash, set the HR. hour with

button (4/12).Then shortly press MODE button (1), the minute digits will ash,

set the MIN. minutes with / button (4/12).

Note: It will return to normal display mode if no key is pressed within 5 seconds.

Mode selection

Repeatedly press MODE (1) button to select different sourcing mode: Radio→

USB →SD/MMC →AUX.

Reset the unit

Operating the unit for the rst time or after replacing the car battery, you must

reset the unit. To set the unit to initial status, press button (18) with a RESET

pointed object. When some errors occur in display, you can also reset the unit,

but it will erase the clock setting and some memorized functions.

SOUND FEATURES

Volume:

To increase or decrease the sound level, rotate knob (5) clockwise or SEL/VOL

counter-clockwise.

Sound Settings

Repeatedly press knob (5) to select the desired mode in the following SEL/ VOL

order: “BAS” (Bass) -> “TRE” (Treble) -> “BAL” (Balance) -> “FAD“ (Fader) ->”

LOUD”(LOUD ON/OFF) -> “LOC”(LOC ON/OFF) -> “AF” (Alternative frequency)

-> “TA” (Traffic announcement) -> “REG” (REG ON/OFF) ->”EON” (EON ON/

OFF) -> “VOL” (Volume). After selecting the desired mode, you can adjust the

current level by rotating knob (5). SEL/ VOL

Note:

- The unit will return to the previous mode if no adjusting happens within 5

seconds.

- Refer to radio section for LOC, AF, TA ,REG and EON.

Switching Loudness On/off

Repeatedly press knob (5) until “LOUD” shows on display, rotate SEL/VOL

SEL/VOL knob (5) to select “LOUD ON” mode to activate LOUDNESS function.

By this function, you can increase the low frequency, which can improve sound

sensitivity. Repeatedly press this button again ,then rotate knob (5) to SEL/VOL

select “LOUD OFF” mode to cancel LOUDNESS function.

CONNECTOR A

4. +12V CONSTANT POWER SUPPLY

5. POWER ANTENNA / AMPLIFIER TURN ON

7. +12V ACCESSORY/SWITCH

8. GROUND

CONNECTOR B

1. REAR RIGHT SPEAKER (+)

2. REAR RIGHT SPEAKER (-)

3. FRONT RIGHT SPEAKER (+)

4. FRONT RIGHT SPEAKER (-)

5. FRONT LEFT SPEAKER (+)

6. FRONT LEFT SPEAKER (-)

7. REAR LEFT SPEAKER (+)

8. REAR LEFT SPEAKER (-)

FIXED ISO FEMALE CONNECTOR

ANTENNA

SOCKET

RCA AUDIO OUT

R (RED)

FUSE

HOLDER

L (WHITE)

WIRING DIAGRAM

AR-3453 IB MUSE 001 REV0 GB.indd1 1 2013-5-3 9:15:13

Specyfikacje produktu

Marka:	Muse
Kategoria:	Radia samochodowe
Model:	M-090 MR
Kolor produktu:	Czarny
Wbudowany wyświetlacz:	Tak
Waga produktu:	650 g
Bluetooth:	Nie
Obsługiwane typy kart pamięci:	MMC, SD, SDHC
Obsługiwane formaty audio:	MP3
Kanały wyjścia audio:	4.0 kan.
Zakresy tunera:	FM, PLL
Ilość stacji:	18
Wymiary produktu (SxGxW):	97 x 178 x 50 mm
Wejście AUX:	Tak
Ustawienia korektora:	Tak
Obsługa typów dysków:	Nie
Dołączony tuner RDS:	Tak
Obsługa znaczników id3:	Tak
Odtwarzacz mp3:	Tak
Wyjścia linii RCA:	2
Odtwarzacz CD-R:	Nie
Odtwarzacz CD-RW:	Nie
Gotowy na iPod:	Nie
Maksymalna moc na kanał:	20 W