Instrukcja obsługi Planet ISW-504PT

Planet przełącznik ISW-504PT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Planet ISW-504PT (2 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2.5 użytkowników na średnio 4.7 gwiazdek

Pobierz PDF

Strona 1/2

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET 5-Port Industrial Ethernet

Switch with 4-Port PoE, ISW-504PT/ISW-514PTF. The interfaces

of these models are shown below:

Model Name 10/100Mbps RJ45

Ports 100FX SFP Slots PoE Ports

ISW-504PT 5 - 4

ISW-514PTF 4 1 4

In the following section, the term “Industrial PoE+ Switch”

means the ISW-504PT/ISW-514PTF.

2. Hardware Introduction

2.1 Switch Front Panel

P1 P2 Fault

120W

PoE Usage

90W

60W

30W

LNK ACT

PoE-in-Use

挖孔

10/100TX

LNK/

ACT

DIP

1~4

VLAN

Extended

OFF

Standard

1 2 3 4 5

ONDIP

LNK ACT

PoE-in-Use

挖孔

P1 P2 Fault

100FX

DIP

1~4

VLAN

Extended

OFF

Standard

120W

PoE Usage

90W

60W

30W

1 2 3 4 5

ONDIP

Figure 2-1:

ISW-504PT front panel

Figure 2-2:

ISW-514PTF front panel

1. Fast Ethernet TP Interfaces

10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meters.

2.3 Switch Upper Panel

The upper panel of the Industrial PoE+ Switch consists of one

terminal block connector within two DC power inputs.

Figure 2-3 shows the upper panel of the Industrial PoE+ Switch.

Input DC 12~48V

Fault max.

load 1A@24V

FaultDC1 DC2

1 2 3 4 5 6

Figure 2-3: Industrial PoE+ Switch Upper Panel

2.4 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of

Industrial PoE+ Switch is used for two DC redundant power

inputs. Please follow the steps below to insert the power wire.

When performing any of the procedures like

inserting the wires or tightening the wire-clamp

screws, make sure the power is OFF to prevent

from getting an electric shock.

2.2 LED Indicators

System

LED Color Function

P1 Green Lights: indicates power 1 has power.

P2 Green Lights: indicates power 2 has power.

FAULT Red Lights: indicates either power 1 or power 2

has no power.

30W Amber

O: indicates the PoE usage is less than

14W.

Blinks: indicates that the PoE usage is

around 15W to 29W.

Lights: indicates the PoE usage is around/

over 30W.

60W Amber

Blinks: indicates that the PoE usage is

around 45W to 59W.

Lights: indicates the PoE usage is around/

over 60W.

90W Amber

Blinks: indicates that the PoE usage is

around 75W to 89W.

Lights: indicates the PoE usage is around/

over 90W.

120W Amber

Blinks: indicates that the PoE usage is

around 100W to 119W.

Lights: indicates the PoE usage is at the

maximum.

Open the box of the Industrial PoE+ Switch and carefully

unpack it. The box should contain the following items:

Industrial PoE+ Switch x 1 User’s Manual x 1

Dust Cap x 5 Wall-mount Kit x 1

If any of these are missing or damaged, please contact your

dealer immediately.

2. 100BASE-FX SFP Slot (ISW-514PTF)

100BASE-FX mini-GBIC slot, SFP (small form-factor plug-

gable) transceiver module: From 2 kilometers (multi-mode

ber) to 20/40/60 kilometers (single-mode ber).

3. DIP Switch

The Industrial PoE+ Switch provides one DIP switch for

Standard, VLAN and Extended mode selections. The

detailed descriptions are shown in the following table.

DIP Switch

Mode Function

Standard Switches 1 to 5 are o.

This mode makes the Industrial PoE+ Switch

operate as a general switch and all PoE ports

operate at 10/100Mbps auto-negotiation.

VLAN

Switch 5 is on.

This mode makes the Industrial PoE+ Switch

operate as a V andLAN isolation switch

1. Ports 1 to 4 will isolate respectively.

2. Ports 1 to 4 can only communicate with Port 5.

Note

After adjusting VLAN DIP switch,

reboot the Industrial PoE+ Switch to

make the change take effect.

Extended Any of switches 1 to 4 is on.

This mode makes the Industrial PoE+ Switch

operate on a per-port basis at 10Mbps full duplex

operation but can support IEEE 802.3af PoE power

output over a distance of up to 250 meters

overcoming the 100m limit on Ethernet UTP cable.

 Per 802.3at PoE+ 10/100BASE-TX Interface (Port 1

to Port 4)

LED Color Function

LNK/

ACT Green

Lights: indicates the link through that port

is successfully established at 10Mbps or

100Mbps.

Blinking: indicates that the switch is

actively sending or receiving data over that

port.

PoE-

in-Use Amber

Lights: indicates the port is providing DC

in-line power.

O: indicates the connected device is not a

PoE powered device (PD).

 Per 10/100BASE-TX Interface (Port 5 of ISW-504PT)

LED Color Function

LNK/

ACT Green

Lights: indicates the link through that port is

successfully established at 10/100Mbps.

Blinking: indicates that the switch is actively

sending or receiving data over that port.

 Per 100FX SFP Slot (Port 5 of ISW-514PTF)

LED Color Function

LNK/

ACT Green

Lights: indicates the link through that port is

successfully established at 100Mbps.

Blinks: indicates that the switch is actively

sending or receiving data over that port.

1. The DC power input range is . Please insert 12V ~ 48V DC

positive and negative DC power wires into contacts 1 and 2

for POWER 1, or 5 and 6 for POWER 2.

Input DC 12~48V

Fault max.

load 1A@24V

FaultDC1 DC2

1 2 3 4 5 6

DC Input Max. PoE Budget

12V 60W

24V 90W

48V 120W

Note

To avoid damage, please use the Industrial PoE+

Switch under its specification.

Specyfikacje produktu

Marka:	Planet
Kategoria:	przełącznik
Model:	ISW-504PT
Kolor produktu:	Czarny
Materiał obudowy:	Metal
Wysokość produktu:	135 mm
Szerokość produktu:	50 mm
Głębokość produktu:	85.1 mm
Waga produktu:	596 g
Certyfikaty:	FCC, CE
Standardy komunikacyjne:	IEEE 802.3af, IEEE 802.3u, IEEE 802.3x
Pełny dupleks:	Tak
Obsługa PoE:	Tak
Zakres temperatur (eksploatacja):	-40 - 75 °C
Zakres wilgotności względnej:	5 - 95 %
Kod zharmonizowanego systemu (HS):	85176990
Diody LED:	Tak
Zakres temperatur (przechowywanie):	-40 - 85 °C
Dopuszczalna wilgotność względna:	5 - 95 %
Stopień ochrony IP:	IP30
Możliwości montowania w stelażu:	Nie
Typ przełącznika:	Nie zarządzany
Podstawowe przełączanie RJ-45 Liczba portów Ethernet:	5
Podstawowe przełączania Ethernet RJ-45 porty typ:	Fast Ethernet (10/100)
Obsługa 10G:	Nie
Wielkość tabeli adresów:	1024 wejścia
Przepustowość rutowania/przełączania:	1 Gbit/s
Produkt stackowalny:	Tak
Montaż naścienny / rzutowanie na sufit:	Tak
Podpora kontroli przepływu:	Tak
Przełącznik wielowarstwowy:	L2
Zasilacz dołączony:	Nie
Automatyczne MDI/MDI-X:	Tak
Store-and-forward:	Tak
Montaż DIN na szynie:	Tak
Wspierany auto-learning adresów MAC:	Tak
Wspierany auto-aging adresów MAC:	Tak
Obsługa zasilania zapasowego (RPS):	Tak
Auto-Negocjacja:	Tak
Funkcje ochrony zasilania:	Krótkie spięcie
Obsługiwane typy kabli:	Cat5, Cat5e, Cat6
Ilość portów Fast Ethernet (PoE):	4
Przepustowość:	0.74 Mpps
Zasilanie przez Ethernet (PoE) zasilanie na port:	15.4 W