Instrukcja obsługi Pyle PASC12

Pyle głośnik PASC12

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PASC12 (7 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 4 użytkowników na średnio 5.0 gwiazdek

Pobierz PDF

Strona 1/7















Introduction

Thank you for purchasing this Pyle Pro PASC series speaker. The

loudspeaker is designed to provide you years of high performance in any

application that you require. Please read this manual carefully to fully

maximize the performance of the speaker.

Features

The PASC series features high-

level drivers and rugged components

and is designed for high-performance

applications.

The cabinet features heavy-duty

construction with reinforced corners. It

is covered with a black-carpeted finish

that will stand up to years of tour duty.

The integrated handles have been

carefully selected for their ergonomic

design and durability.

Both models are loaded with a premium Kapton voice coil woofer and

exhibit excellent bass response. The compression driver provides warm

midrange reproduction and crystal clear highs.

The integrated passive crossover network is assembled using quality

components and efficiently directs the frequencies to the proper drivers.

Connections

Your PASC series

speaker has an extremely

flexible connection panel.

There are two Speakon jacks

as well as two ¼” jacks. You

can also hookup your speaker

cabinet using the “Quick

Connect” speaker terminals,

which accommodate either

wire leads or a banana plug.

The jacks are wired in



parallel, which allows you to daisy chain additional speakers. Thus you can

use one amplifier channel to power multiple speakers.

Make certain that the wires you are using are at least 12 gauge

unshielded speaker cable (the lower the number, the thicker the wire). Do

not use shielded “instrument” cables.

Hooking speakers up in parallel decreases the overall

impedance, placing a greater load on the amplifier. Check your

amplifier’s specifications to ensure that you are not overloading

the channel.

CAUTION: DO NOT US E MORE THAN ONE JACK AS AN

AMPLIFIER INPUT. DOING S O WILL DAMAGE THE S PEAKER!

Amplifier Requirements

Check the product specifications (page 5) to see the power handling

for your model. There are a couple of considerations to keep in mind when

choosing an amplifier to drive your PASC series speaker. While it is true

that an amplifier with a higher power rating can damage the drivers, under-

powering can be even more dangerous. When an amplifier is overdriven and

starts distorting, it generates transient frequencies that are much louder than

the program material. These wayward frequencies could damage your

speaker. A proper match is an amplifier which could drive the speaker up to

the cabinet’s RMS rating, without exceeding the amplifier’s own RMS level.

Operation

When powering on your equipment, make sure the volume level on

the amplifier is turned all the way down. This is to avoid the “popping”

noise, which could damage your speaker.

The placement of speakers can be a bit tricky. This is especially true

to monitors as they are more susceptible to feedback. Being that a monitor is

meant to face the performers, the chances of feedback are much greater. The

trick is to place the monitor outside the microphone’s pickup pattern. For

most microphones the best position is directly behind the mic. Supercardioid

mics however, do not reject sound from the back very well, but do have a

Specyfikacje produktu

Marka:	Pyle
Kategoria:	głośnik
Model:	PASC12
Kolor produktu:	Czarny
Rodzaj zasilania:	Prąd przemienny
Technologia łączności:	Przewodowa
Impedancja:	8 Ω
Moc wyjściowa (RMS):	300 W
Kanały wyjścia audio:	1.0 kan.
Zasięg częstotliwości:	40 - 20000 Hz
Rozmieszczenie głośników:	Podłoga
Ilość przetworników:	1
Głośnik wysokotonowy:	Tak
Głośnik niskotonowy:	Tak
Czułość:	101 dB
Waga (imperialna):	37.5 funtów
Moc szczytowa (PMPO):	600 W
Wymiary (SxGxW) (imperialne):	25.6 x 13 x 17.3 "
Średnica głośnika niskotonowego (imperial):	12 "