Instrukcja obsługi Pyle PLMR77U

Pyle subwoofer PLMR77U

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PLMR77U (16 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.7 gwiazdek

Pobierz PDF

Strona 1/16

Marine Stereo Receiver Power Amplifier

AM/FM/MP3/USB/AUX/SD Card Reader

Marine Stereo Receiver, Single DIN,

30 Preset Memory Stations, LCD Display

with Remote Control

www PyleUSA com

INSTALLATION

Preparation

The preparation kit is necessary to mount the radio on the dashboard, this kit is

available at electronics stores and car audio specialists, check the installation kit

before using it to make sure it is the right one for your vehicle.

INSTALL THE DEVICE

1. Lift the left or right top corner of the plastic outer trim ring

then pull it out to remove it.

2. Insert the two bracket keys into the left and right side of

the chassis to separate the chassis from the housing.

3. Install the mounting knob on the board. Check the

opening size of the sliding panel to be mounted. If the

measurement is not large enough, carefully cut it until it

slips easily on the opening. Do not force the handle in the

opening so as not to bend it. Locate the series of dubbing

tabs above, below and all sides to be mounted. Completely

insert it to the opening of the board, bend the tabs as

necessary towards outside to ensure it ts the board.

4. Slide the stereo into the opening in the dash, ensuring that

the wires behind are tucked and not pinched.

5. Follow the wiring diagram carefully.

Verify you’ve connected them correctly.

CAUTION! Connect the unit to a 12 Volt power source

with adequate ground.

6. Now that your wires are all completed, attach the front

panel and turn the unit (the vehicle must be switched on). If the unit does not ON

work, check the calibration again until the problem is solved. With the new car

stereo secured into the bracket, all you need to do is plug the wiring harness back

into the stereo and put the assembly back into place.

7. Slide the stereo into the opening in the dash, ensuring that the wires behind are

tucked and not pinched. Sometimes this may take a few times when the vehicle

has a tight dash opening. Tuck the wires back into an opening behind the unit.

8. Install the plastic outer trim ring

9. Snap all the pieces of trim back into place over the stereo. Double check that all

screws and trim pieces are securely in place.Try out the new stereo. Turn the car

power on again and play around with the stereo and its settings to be sure

everything is in working order.

www PyleUSA com

WIRING CONNECTIONS

CONTROL PANEL BUTTONS

WIRING DIAGRAM

PRECAUTION

+12V DC

NEGATIVE

EARTH

AMPLIFIER OUTPUT

White: Rear Output

Left

White: Front Output

Left

Red: Right Front Output

Red: Rear Right Output

7 8 9 10 11 12 13

2021

Specyfikacje produktu

Marka:	Pyle
Kategoria:	subwoofer
Model:	PLMR77U
Kolor produktu:	Biały
Materiał obudowy:	Metal,Plastic
Regulowany termostat:	Tak
Wbudowany wyłącznik:	Tak
Typ kontroli:	obrotowy
Długość przewodu:	1.35 m
Automatyczne wyłączanie zasilania:	Tak
Wysokość produktu:	289 mm
Szerokość produktu:	196 mm
Głębokość produktu:	143 mm
Waga produktu:	1600 g
Model:	Wentylator elektryczny ogrzewacza pomieszczeń
Zabezpieczenie przed przegrzaniem:	Tak
Moc grzewcza:	1800 W
Moc grzewcza (min):	900 W
Opcje rozmieszczania:	Podłoga
Stopień ochrony IP:	IP21
Liczba poziomów zasilania:	2
Odpowiedni dla:	Wewnętrzna
Zakres oscylacji:	70 °
Automatyczna oscylacja:	Tak