Instrukcja obsługi Pyle PLMRC500X1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PLMRC500X1 (12 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.2 gwiazdek
Strona 1/12
Mono-Block Weather Resistant Audio Amplifier System
PLMRC500X1
Class D Compact Designed Suit for Car, ATV,
UTV, 4X4, Jeep, Motorcycle and Marine,
and any other Weather Resistant Application
www.PyleUSA.com
2
INTRODUCTION
This power amplier has been designed to provide high quality performance
with a minimum of maintenance. However, it's performance will only be as good
as the care and quality of components with which is installed.
We therefore advise that you read these instructions very carefully to familiarize
yourself with the product and it's features.
Before installing the power amplier please read this instruction manual
carefully. The instructions for mounting and connecting the set have to be
followed precisely. If necessary, a service center should be consulted.
All connections for DC power, signal input and speaker outputs can be carried
out easily and safely byway of RCA and screwed terminals.
INSTALLATION INSTRUCTIONS
Please choose a mounting place without any direct weather inuences.
Note that the amplier generates heat so that a well ventilated place is necessary.
According to your car's construction the set can be made very carefully in order
to ensure the amplier's full performance and reliability.
Keep the wire connections as short as possible with sucient dimensions in
order to minimize power losses and provide a higher audio output of the system.
For safety reasons route all power and speaker wiring by using the exiting wire
channels. To minimize damage to the cables, take care that they do not pass
sharp edged metal. Lay all cables as far away as possible from the ignition cables,
modules in the boot and under the key dashboard, as this create interference.
Add a fuse into the (+) power cable in a distance of not more than 30 cm from
the positive battery pole.
Keep the length of the power wires as short as possible. It is better to use power
cables which are short and then longer speaker cables.
In order to reduce interference, also pay attention to the instructions.
www.PyleUSA.com 3
PRECAUTIONS
• This unit is designed for negative ground 12-14.50 VoIts (DC) operation only
• Use speakers with an impedance of 1 to 4 Ohms (2 to 8 Ohm when used as
bridged two amplier)
• Avoid installing the unit where:
•It would be subject to high temperatures, such as from direct sunlight or hot
air from the heater.
•It would be exposed to rain or moisture.
•It would be subject to dust or dirt.
• If your car is parked in direct sunlight and there is a considerable rise in
temperature inside the car, allow the unit to cool o before operation.
• When installing the unit horizontally, be sure not to cover the heatsink ns
with the oor carpet.
• If this unit is placed too close to the car radio, an interference may occur in this
case, separate the amplier from the car radio.
• This power amplier employs a protection circuit to protect the transistors and
speakers if the amplier malfunctions.
• Do not attempt to test the protection circuits by covering the heatsink or
connecting improper loads.
• Do not use the unit with a weak auto battery as its optimum performance
depends on a normal battery supply voltage.
• For safety reasons, keep the volume of your car audio system moderate so that
you can still hear normal trac sounds outside your car.
FUSE REPLACEMENT
If the fuse blows, check the power connection and replace the fuse. If the fuse
blows again after replacement, there may be an internal malfunction.
In this case, consult your dealer.
WARNING: Use the specied amperage fuse. Use of a higher amperage fuse
may cause serious damage.
PROTECTION CIRCUIT
This amplier is provided with a protection circuit which operates in the
following cases when:
• the unit is overheated.
• the speaker terminals are short circuited.
Specyfikacje produktu
| Marka: | Pyle |
| Kategoria: | odbiornik |
| Model: | PLMRC500X1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Pyle PLMRC500X1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje odbiornik Pyle
13 Stycznia 2025
6 Grudnia 2024
6 Grudnia 2024
8 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
30 Września 2024
29 Września 2024
Instrukcje odbiornik
- odbiornik James
- odbiornik PTN-electronics
- odbiornik Fishman
- odbiornik Hama
- odbiornik Audison
- odbiornik Redline
- odbiornik ICOM
- odbiornik GOgroove
- odbiornik Extron
- odbiornik Alecto
- odbiornik Camille Bauer
- odbiornik Nokia
- odbiornik Brondi
- odbiornik CSL
- odbiornik Pinnacle
Najnowsze instrukcje dla odbiornik
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
30 Marca 2025