Instrukcja obsługi Pyle PWPBT15
Pyle
Kołyska/stacja dokująca
PWPBT15
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PWPBT15 (1 stron) w kategorii Kołyska/stacja dokująca. Ta instrukcja była pomocna dla 41 osób i została oceniona przez 21 użytkowników na średnio 4.1 gwiazdek
Strona 1/1
Location of controlsLocation of controls
1. Open the cover on the bottom end of the speaker.
2. Connect the small end of the Micro USB charging
cord into the DC5V charging port on the end of the
speaker.
3. Connect the other end of the Micro USB cable to
your computer’s USB port.
4. The LED light on the top panel of the speaker lights
up RED when charging.
5. The LED light turns o when nished
charging (approximately 4 hours).
6. Close the cover on the bottom of the speaker.
Charging the Bluetooth SpeakerCharging the Bluetooth Speaker
Pairing the speaker with a Bluetooth
enabled device
Pairing the speaker with a Bluetooth
enabled device
Bluetooth
Speaker
Micro USB
Charging
Cable
1. Make sure your Bluetooth device supports A2DP prole.
2. Turn up the volume on your Bluetooth device.
3. You may have to unpair the speaker, then re-pair to your
device.
1. Make sure the Bluetooth Speaker is turned ON before
beginning the pairing process.
2. Keep your Bluetooth Speaker and Bluetooth enabled
device within 3 feet of each other during the pairing
process.
3. Press and hold the [ MODE ] button. The LED light on
the speaker will ash BLUE.
4. Check that YOUR device’s Bluetooth feature is turned ON.
5. Try repeating the pairing process, see “Pairing the Speaker
with a Bluetooth enabled device”.
My Bluetooth Device is not able to pair with the
Bluetooth Speaker.
I can pair the Bluetooth Speaker with my Bluetooth
device, but I cannot hear any music?
Troubleshooting tipsTroubleshooting tips
1. Make sure the Bluetooth Speaker is turned ON before
beginning the pairing process.
2. Press and hold the [ MODE ] button. The LED light on
the speaker will ash BLUE.
3. The speaker is now in pairing mode
I cannot get the Bluetooth Speaker into Pairing Mode.
Legal informationLegal information
Limited Warranty
within 3 feet
The screenshots above are typical of many Bluetooth
enabled devices in the market today, and are used
to assist in the explanation of the pairing process.
Your Bluetooth enabled device’s interface and
interaction with the Bluetooth Speaker may
slightly dier from the illustrations above.
1. Make sure the Bluetooth Speaker is turned o.
2. Keep your Bluetooth Speaker and Bluetooth
enabled device within 3 feet of each other during
the pairing process.
3. Slide the switch to the ON position. Power ON/OFF
The LED light will ash quickly.
4. Press and hold the [ Mode] button. An audible
signal will be emitted and the LED will blink
steadily. The speaker is now in pairing mode.
5. Set your mobile phone or other Bluetooth enabled
device to search for Bluetooth devices.
Using your Bluetooth SpeakerUsing your Bluetooth Speaker Playing musicPlaying music
Most media enabled smart phones will display
“Connected to phone audio and media” when
connecting to the Bluetooth Speaker. This means
you can make phone calls and enjoy your music.
To enjoy wireless music on your Bluetooth Speaker,
make sure you are connected to a Bluetooth enabled
device. Once connected you can press PLAY on your
Bluetooth device or you can press the [ MODE ]
button on the PBT604 Bluetooth Speaker.
Once playback has begun, you can control the music
or answer phone calls from the control buttons of the
Bluetooth speaker (with devices that have the AVRCP
Bluetooth prole).
Skipping or searching songs
(With devices that have AVRCP Bluetooth prole)
tPress the [ VOL+] button to go to the next song.
tPress the [ VOL- ] button to go to the previous
song.
Music Controls
1. LED Light
2. [ VOL- ] button: tVolume Down (hold)
tPrevious Track (quickpress)
3. : [ MODE ] button tPlay/Pause (quickpress)
tAnswer Call/End Call (quickpress)
4. : [ VOL+ ] button tVolume Up (hold)
t Next Track (quickpress)
5. Microphone
6. Power On/O switch
7. Micro USB DC5V charging port
8. 3.5mm auxilliary input
9. Hook
10. Volume knob
USB Charging
Cable
Micro USB
Charging Port
Speaker
PC Should you have any questions or problems concerning this
product, please contact our customer service department at:
Customer Support:
718-535-1800 ext: 279
support@pyleaudio.com
TO OBTAIN WARRANTY SERVICE:
Provide proof of the date of purchase within the package
(Dated bill of sale).
Prepay all shipping costs to the authorized service center,
and remember to insure your return.
Include a return shipping address (no P.O. Boxes), a
telephone contact number, and the defective unit within
the package.
Describe the defect or reason you are returning the
product.
Your product will be repaired or replaced, at our option, for
the same or similar model of equal value if examination by
the service center determines this product is defective.
Products received damaged as a result of shipping will
require you to le a claim with the carrier.
The shipping address of the authorized service center is:
Pyle Service Center
1600 63rd Steet
Brooklyn, NY 11204
You will also need to include a $20 money
order to cover the return shipping. It will take
roughly 2-3 weeks for the product to be
returned back to you. Please let us know
if this is being shipped from outside the US
before you ship it.
90 Days Limited Warranty
In the unlikely event that this product is defective, or does
not perform properly, you may within ninety (90) days from
your original date of purchase return it to the authorized
service center for repair or exchange.
FCC Part 15:
This equipment has been tested and found to comply with the
requirements for a Class B digital device under Part 15 of the Federal
Communications Commission (FCC) rules. These requirements are
intended to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
t3FPSJFOUPSSFMPDBUFUIFSFDFJWJOHBOUFOOB
t*ODSFBTFUIFTFQBSBUJPOCFUXFFOUIFFRVJQNFOUBOESFDFJWFS
t$POOFDUUIFFRVJQNFOUJOUPBOPVUMFUPOBDJSDVJUEJòFSFOUGSPN
that to which the receiver is connected.
t$POTVMUUIFEFBMFSPSBOFYQFSJFODFESBEJP57UFDIOJDJBOGPSIFMQ
Do not attempt to repair or modify this equipment.
8BSOJOH$IBOHFTPSNPEJöDBUJPOTUPUIJTFRVJQNFOUOPUFYQSFTTMZ
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
i5IJTEFWJDFDPNQMJFTXJUI1BSUPGUIF'$$3VMFT0QFSBUJPOJT
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.”
PWPBT15
User Guide
3.5mm
Auxilliary
Cord
32
1
8
4
MIC
9
10
5
76
ON/OFF DC 5V AUX
On an iPhone
tGo to SETTINGS > GENERAL > BLUETOOTH
(Make sure Bluetooth is turned ON)
Paired
Bluetoot h
General
Bluetooth
ON
SBT604
Devices
Now dis coverable
12:12 PM
On a Blackberry
t(PUP4&55*/(4015*0/4#-6&5005)
t&OBCMF#-6&5005)
Bluetooth:
Discoverable:
Paired Devices
SBT604
Bluetoo th 3G
On
Yes
Add New Device
On an Android Phone
tGo to SETTINGS > BLUETOOTH > MENU >
Search
Bluetooth settings
Bluetooth devic es Sca nning
Bluetooth
Device name
SBT604
Visible
Search for devices
Make devi ce visibl e
12:12 PM
On other Cell Phones/Devices
tReview the instruction manual that came
with your phone/device.
Searching for devices
Paired Devices:
1 found
Stop
*Empty *
Bluetooth: Enabled
6. When the Bluetooth enabled device nds the
speaker, select PWPBT15 from the list of found
devices.
7. If required, enter the password 0000. Select OK
or Yes to pair the two units.
8. After a successful registration, the LED Indicator
light will become solid BLUE.
Note: If the speaker has already been connected
to the Bluetooth device/phone, the speaker will
reconnect with the Bluetooth device/phone
automatically when turned on.
Make sure you charge the speaker for 8 hours
before using it for the rst time.
ON/OFF DC 5V AUX
Powering ON/OFF
t To turn ON Power ON/OFF, slide the switch to the
ON position.
t To turn OFF Power ON/OFF, slide the switch to the
OFF position.
Adjusting the volume
Way 1: Rotate the Volume Knob to adjust the volume
to the desired level.
Way 2: Press and hold the button to [ VOL+]
increase the volume and the [ VOL-]
button to decrease it to your desired level.
You may also adjust the volume from your
mobile phone’s volume control.
Answering/Ending a call
t To answer a call, quickpress the button.[ MODE ]
t To end a call, quick press the button.[ MODE]
To make a call
Dial the number and press the send button on your
mobile phone. The call is automatically transferred to
the speaker.
Play/Pause
Press the button to pause the music. [ MODE ]
To resume music playback, press the [ MODE ]
button again.
You may also adjust the volume from your
mobile phone’s volume control.
Adjusting the volume
Way 1: Rotate the Volume Knob to adjust the volume
to the desired level.
Way 2: Press and hold the button to [ VOL+]
increase the volume and the [ VOL-]
button to decrease it to your desired level.
21 3
MIC
1. [ VOL- ] button: tVolume Down (hold)
tPrevious Track (quickpress)
2. [ MODE ] button: tPlay/Pause (quickpress)
tAnswer Call/End Call (quickpress)
3. : [ VOL+ ] button tVolume Up (hold)
t Next Track (quickpress)
Product maintenanceProduct maintenance
tPower o this product when not in use.
tDO NOT expose this product to water or other
liquids.
tDO NOT use abrasive cleaning solvents to clean the
Bluetooth Speaker
tIf you will not use the Bluetooth Speaker for long
periods, be sure to store it in a dry place, free from
extreme temperature, humidity and dust.
Using as a wired speakerUsing as a wired speaker
The PWPBT15 can be used as a wired speaker by using
the included 3.5mm Auxiliary Cord.
1. Plug one end of the Auxiliary Cord into the AUX jack
on the side of the speaker.
2. Plug the other end of the Auxiliary Cord into the
headphone jack of any media device that has a 3.5mm
headphone jack (this is a standard headphone-out
jack).
3. Use your media device's music controls to control
the music. Only volume can be controlled when
connected to a device using the Auxiliary Cord.
Certain Bluetooth features including those listed may
not be supported by all compatible Bluetooth-enabled
devices, and/or the functionality of such features may
be limited in certain devices.
In order for Bluetooth devices to communicate with
one another properly, they must utilize the same
Bluetooth prole. To determine the proles
supported by your device (mobile phone, computer
or MP3 player), please refer to the device’s user
guide.
Specyfikacje produktu
| Marka: | Pyle |
| Kategoria: | Kołyska/stacja dokująca |
| Model: | PWPBT15 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Pyle PWPBT15, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Kołyska/stacja dokująca Pyle
15 Stycznia 2025
4 Października 2024
20 Września 2024
13 Września 2024
11 Września 2024
5 Września 2024
5 Września 2024
3 Września 2024
2 Września 2024
2 Września 2024
Instrukcje Kołyska/stacja dokująca
Najnowsze instrukcje dla Kołyska/stacja dokująca
31 Marca 2025
26 Marca 2025
12 Marca 2025
12 Marca 2025
10 Marca 2025
27 Lutego 2025
27 Lutego 2025
11 Lutego 2025
7 Lutego 2025
7 Lutego 2025