Instrukcja obsługi Samsung SKK-9MCV
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Samsung SKK-9MCV (3 stron) w kategorii pralka. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 7 użytkowników na średnio 4.3 gwiazdek
Strona 1/3
Stacking Kit Installation Guide (SKK-9MC*)
CAUTION
• Risk of personal injury. The dryer is large and heavy. Have at least two people move the dryer. Otherwise, it
may result in personal injury or death.
• Risk of product damage during installation. The dryer must be firmly installed on top of the washer. Do not
install the washer on top of the dryer. Otherwise, it may result in personal injury, death, or property damage.
• Risk of electric shock. You must disconnect the power cord before installing the product. Otherwise, it may
result in severe personal injury or death.
• When installing the dryer on top of the washer, make sure the drain hose in the rear is connected directly to
a drain and not to a water tank.
NOTE
This Stacking Kit is compatible with Samsung BESPOKE front-load washers and dryers released after 2022.
Check the compatibility of the stacking kit before installing it. You can check the compatible washer and dryer
models at the Samsung website (www.samsung.com).
Accessories
Hex-head screws (4)
6002-001431 (M5, L16)
Washers (4)
DC60-00044A (ID5, OD10)
Phillips-pan head
screws (8)
6002-000213 (M4, L12)
Phillips-pan head
screws (2)
6002-000215 (M4, L16)
:9($Ꮬ
:;($
Ꮪ
R
R
4.5cf
21kg
5.0cf23kg
Installation guide Left side top cover bracket Right side top cover
bracket (with multi-
connection cable
attached)
Front cover
Bracket guide Stacking guide (L/R)
Installation
STEP 1
Tighten the four leveling feet of the dryer all the way.
• Level the dryer using a level.
STEP 2
Slightly pull out the installed washer to gain access to
its rear.
Unfasten the two screws attached at the back of the
washer.
=H8 #
:;($
<H> #
:9($
STEP 3
Check the capacity of your washer (5.0 cf and over or
4.6 cf and less) and locate the correct assembly holes on
the top cover bracket (L/R).
<H= #
:9($
=H8 #
:;($
=H8 #
:;($
<H> #
:9($
Top cover bracket
Stacking guide
STEP 4
Fasten the top cover brackets (L/R) to their
corresponding stacking guides (L/R) using four M4 x L12
Phillips-Pan head screws.
• Check and make sure each top cover brackets are on
the correct sides (left/right) of the stacking guides
before fastening them.
R
R
4.5 cf21k g
5.0 cf23 k g
4.5 cf21k g
5.0 cf23 k g
L
4.5cf
21kg
5.0
23kg
R
STEP 5
Position the assembled stacking guides (L/R) on the
curved edges of the washer’s top cover. Fasten the
assembled stacking guides (L/R) using four washers and
M5 x L16 hex-head screws.
:9(
$Ꮭ
:;($
Ꮫ
:9
($Ꮬ
:;($
Ꮪ
STEP 6
Assemble the bracket guide to the stacking guides at
the front end and check the alignment. Remove the
release liner from the double-sided tape attached
to the bottom of the stacking guides and attach the
stacking guides to the washer as shown in the figure.
Then, disassemble the bracket guide from the stacking
guides.
CAUTION
• Make sure the bottom curvature of the stacking
guide is aligned with the curvature of the washer’s
top cover.
• Attach the stacking guides after making sure they
are perfectly parallel with the washer’s top cover.
• After attaching the stacking guides, reattach the
bracket guide and double-check to make sure the
stacking guides are parallel.
STEP 7
Have at least two people lift the dryer and place it on
the stacking guide, and then push the dryer until the
rear two legs are properly locked into the stacking
guides’ U-shaped slot.
STEP 8
If installed correctly, the front edges of the stacking
guides should be perfectly aligned with the front edges
of the dryer’s side frames.
• Check to make sure the front edges of the dryer’s
side frame are not sticking out past the stacking
guides.
STEP 9
Attach the bracket guide to the stacking guides and
secure it in place using the M4 x L16 Phillips-Pan head
screws, as shown in the figure.
STEP 10
Hold the front cover with the letter ‘UP’ facing upward.
Align the hooks on the front cover with the holes on
the stacking guides as shown in the figure. Then, fully
insert the hooks to attach the front cover to the staking
guides.
<H= #:9(
$
<H= #:9($
<H= #:9($
<H= #:9($
STEP 11
Open the connector port covers on the dryer and the
washer. Then, connect the multi-connection cable on
both ports and close both connector port covers.
Attach each wire holder to the designated slots on the
dryer and the washer.
DC68-03859G-00
SKK-9MC_StackingKit_IG_DC68-03859G-00_EN+CFR+MES.indd 1 2022-04-11 9:02:13
Specyfikacje produktu
| Marka: | Samsung |
| Kategoria: | pralka |
| Model: | SKK-9MCV |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Samsung SKK-9MCV, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje pralka Samsung
8 Kwietnia 2025
8 Kwietnia 2025
6 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
Instrukcje pralka
- Iberna
- Aspes
- Morris
- MPM
- SIBIR
- VOX
- Mio Star
- Pelgrim
- Electra
- Element
- Marynen
- Haden
- Freggia
- Mabe
- Zoppas
Najnowsze instrukcje dla pralka
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025