Instrukcja obsługi Siemens WM10Q37XEE

Siemens pralka WM10Q37XEE

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Siemens WM10Q37XEE (6 stron) w kategorii pralka. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.9 gwiazdek

Pobierz PDF

Strona 1/6

Safety instructions

 The washing machine is heavy - take care when lifting.

 Caution: frozen hoses may rip/burst. Do not install the washing machine in areas exposed

to frost or outdoors.

 The washing machine could be damaged. Do not lift the appliance by protruding

components (e.g. the washing machine door, the cover, the front panel or the outer door

in case of deco models).

 In addition to the instructions provided in this document, special regulations from the

relevant water and electric utility companies may apply.

 If in doubt, have a technician connect the appliance.

 Lay hoses and cables in such a way that there is no risk of tripping.

Installation surface

 The machine must be stable so that it does not move around.

 The installation surface must be firm and level.

 Soft floors/floor coverings are not suitable.

Installation on a pedestal

 The feet of the washing machine be secured with holding brackets*.must

* order no. WMZ2200, WX9756, CZ110600, Z7080X0

Installation on a wood joist floor

 If possible, place the washing machine in a corner.

 Screw a water-resistant wooden board (min. 30 mm thick) to the floor.

 The feet of the washing machine be secured with holding brackets*.must

* order no. see above

Installation on a platform with drawer*

 * order no. WMZ20490, WZ20490

Installing the appliance

Install the appliance before connecting it to the power supply.

Installation in a kitchenette (underneath the worktop or fitted in a cabinet)

 Recess width of 60 cm required.

 Only install the washing machine underneath a continuous worktop that is securely

connected to adjacent cabinets.

Installation underneath the worktop

Risk of electric shock!

Instead of the appliance covering plate, you have a metal cover*must .

* order no. WMZ20331, WZ20331

 Recess width of 60 cm required.

Scope of delivery depending on model

Also required, depending on the connection:

 1 hose clamp Ø 24-40 mm (exclusive dealers) to connect to a siphon

apage 4; water connection.

Useful tools

 Spirit level for installation.

 Wrenches

WAF 13: for loosening transport braces and apage 3

WAF 17: for aligning appliance feet .apage 5

Hose and cable lengths depending on model

Left-hand connection or Right-hand connection

Available from specialist dealers/the after-sales service:

 Extension for Aqua-Stop or cold-water inlet hose (approx. 2.50 m),

order no. WMZ2380, WZ10130, CZ11350, Z7070X0

 Longer inlet hose (approx. 2.20 m) for standard model.

Mains cable

Water outlet

Water inlet

Elbow

for fixing the drainage

hose in place

Covers

Aqua Stop Hot wateräAqua Secure & ä

Standard

Adapter 1/2-3/4

(depending on model)

~145 cm

~100 cm

~135 cm

~145 cm

min. 60 cm

max. 100 cm

~90 cm

Moisture inside the drum

is due to final testing.

Removing the transport braces

 Before using the appliance for the first time, make sure that you

completely remove transport braces and keep them for

subsequent transportation.

 If you need to transport the appliance at a later date, always re-affix

the transport braces to prevent damage to the machine. apage 6.

 Store the screw and sleeve together.

1. Take the hoses out of the holders.

2. Remove all 4 screws completely.

3. Remove all 4 transport braces completely and take the mains cable

out of the holders .(depending on model)

4. Affix the covers.

Water connection depending on model

 Do not immerse the Aqua-Stop safety device in water Risk of electric shock.

(contains an electric valve).

 To prevent leaks or water damage, observe the instructions in this section.

 : only operate the washing machine using cold drinking water (in case of models Caution

featured for hot water: maximum temperature 60 ºC).

 Do not connect to the mixer tap of an unpressurised hot-water boiler.

 Do not use a used inlet hose. Only use the inlet hose supplied or one which was

purchased from an authorised specialist dealer.

 If in doubt, have a technician connect the appliance.

Water connection depending on model

QWater inlet

Caution: do not bend, squash, modify or cut through

(otherwise its strength is no longer guaranteed).

Optimum water pressure in the supply network: 200 1,000 kPa (2 10 bar)ä ä

 When the tap is on, the water flow is at least 10 l/min

(1-2 bar: 6 l/min; with 1 bar consumption parameters cannot be assure).

 If the water pressure is higher than this, a pressure reducing valve must be installed

Connection to the tap:

Aqua-Stop, Aqua-Secure, Standard: Connection to the

machine:

Aqua Stop, Aqua-Secure Standardä

no necessary with Aqua-

Stop, fixed installation;

Aqua-Secure, Standard

1. Connect the water inlet hose (hoses) to the tap (taps) 3/4" = 26,4 mm and to the solenoid

valves.

Caution: only tighten the screw connections by hand.

2. Open the water tap (taps) carefully, checking the leak tightness of the connection points.

Caution: the screw connection is under mains water pressure.

Connection in case of hot water

models:

COLD  Cold water

HOT  Hot water max. 60 °C (red)

If no hot water connection is present:

 only connect the cold water inlet hose

and

 cover the hot water connection on the

appliance so that it is kept free of dirt.

QWater outlet

Caution: do not bend or pull lengthways.

Height difference between the installation surface and the

drain:

min. 60 cm - max. 100 cm

Outlet in a sink:

Caution: secure the drain hose from slipping out.

Caution: the plug must not block drainage from the sink. During

pumping, check whether the water is draining away quickly

enough. The end of the drain hose must not be immersed in the

water pumped out. This risks water being sucked back into the

washing machine.

Drainage into a siphon:

Caution: the connection point must be secured with a hose

clamp, Ø 24-40 mm (exclusive dealers).

max.

90°

max.

90°

Specyfikacje produktu

Marka:	Siemens
Kategoria:	pralka
Model:	WM10Q37XEE
Kolor produktu:	Czarny, Srebrny
Położenie urządzenia:	Wolnostojący
Częstotliwość wejściowa AC:	50 - 60 Hz
Napięcie wejściowe AC:	220 - 240 V
Wysokość produktu:	850 mm
Szerokość produktu:	595 mm
Głębokość produktu:	584 mm
Opóźniony start czasomierza:	Tak
Klasa wydajności energetycznej:	C
Typ ładowania:	Od przodu
Zawias drzwiczek:	Lewy
Pojemność znamionowa:	7 kg