Instrukcja obsługi Sunding SD-576B
Sunding
komputer rowerowy
SD-576B
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sunding SD-576B (2 stron) w kategorii komputer rowerowy. Ta instrukcja była pomocna dla 28 osób i została oceniona przez 14.5 użytkowników na średnio 4.9 gwiazdek
Strona 1/2
tire size
circumference
tire size
circumference
tire size
circumference
12×1.75 935
12×1.95 940
14×1.50 1020
14×1.75 1055
16×1.50 1185
16×1.75 1195
16×2.00 1245
16×1-1/8 1290
16×1-3/8 1300
17×1-1/4 1340
18×1.50 1340
18×1.75 1350
20×1.25 1450
20×1.35 1460
20×1.50 1490
20×1.75 1515
20×1.95 1565
22×1-3/8 1770
22×1-1/2 1785
24×1.75 1890
24×2.00 1925
24×2.125 1965
24×1(520) 1753
24×/34Tubular 1785
24×1-1/8 1795
24×1-1/4 1905
26×1(599) 1913
26×1.25 1950
26×1.40 2005
26×1.50 2010
26×1.75 2023
26×1.95 2050
26×2.10 2068
26×2.125 2070
26×2.35 2083
26×3.00 2170
26×1-1/8 1970
26×1-3/8 2068
26×1-1/2 2100
26×7/8 1920
650×20C 1938
650×23C 1944
650×25C 1952
650×38A 2125
650×38B 2105
27×1(630) 2145
27×1-1/8 2155
27×1-1/4 2161
27×1-3/8 2169
27.5×1.50 2079
27.5×1.95 2090
27.5×2.1 2148
27.5×2.25 2182
700×18C 2070
700×19C 2080
700×20C 2086
700×23C 2096
700×25C 2105
700×28C 2136
700×30C 2146
700×32C 2155
700Tubular 2130
700×35C 2168
700×38C 2180
700×40C 2200
700×42C 2224
700×44C 2235
700×45C 2242
700×47C 2268
29×2.1 2288
29×2.2 2298
29×2.3 2326
CLK Mode(12H/24H)
Sensor Wiring
Computer Battery Installation
While the default Maintenance Alert digit
200 RIGHTkm/m is flas hing, Press the button
to choose km/m. Press the 200/400/600/800
left button to confirm and enter into Clock
mode. (when the the Maintenance ODO
Alert digit you setted, the will appear on
the screen to alert the rider, press the RIGHT
button seconds to cancel it.)3
SPD CURRENT SPEED
ODO ODOMETER (0.001~99999km/m)
DST TRIP DISTANCE
MXS MAXIMUM SPEED
AVS AVERAGE SPEED
TM ELAPSED TIME
CLK CLOCK (12H/24H)
SCAN
“-” “+” COMPARATOR
SETTING SPEED SCALE ,(km/h m/h)
SETTING TYRE CIRCUMFERENCE (0mm~9999mm)
SETTING THE LAST VALUE OF ODOMETER /ODO
MAINTENANCE ALERT
FREEZE FRAME MEMORY
DOUBLE CELL BOXES
BACK LIGHT
AUTO ON OFF /
SD-576B (17 function)
FUNCTIONS
Remove the battery cover from the bottom of
the computer by using a flat blade screwdriver,
install one CR2032 battery with the positive (+)
pole facing the battery cover and replace the
cover. Should the LCD show irregular figures,
take out the battery and reinstall it.
Speedometer Sensor
Attach the sensor transmitter to either front fork using the supplied cable
ties. Fit the magnet to a spoke using the diagram above as a guide.
Position the sensor & magnet as shown above. Take care to align the
magnet to either arrow on the sensor with 3mm gap in between.
Route the sensor wire up the fork blade,
using the cable ties to secure it. Make
sure it does not hinder the movement
of the front wheel.
Mounting Shoe
Attach the mounting shoe with the cable ties
to thehandlebars as shown in the diagram.
Attach the comprter to the mounting shoe by
slidingthe unit until it snaps firmly into bosition. To remove, press down on
therelease catch, and remove the computer.
To check for proper speed function and sensor alignment, spin the front
wheel withthe computer in speed mode. Adujst the position of sensor and
magnet if there is onor weak signal.
Computer
Wheel Size Input
‘ ’ appears on the screed when the battery has been installde, with 2060
one figure flashing enter the wheel circumerence using the formula below.
In the example above you would enter . Press the button to 2198 RIGHT
advance the digits as nedded and the button to confirm and LEFT
advance. (The circumference ranges 0mm~9999mm), press the LEFT
button to enter mode.KM/M
Setting(km/h)/(m/h)
Press the button to choose or .RIGHT km/h m/h
Press the button to enter mode.LEFT CLOCK
Setting Maintenance alert
In Mode, press the button for seconds CLOCK LEFT 5
to enter selection. Press once more to swap 12/24H
between hours. Press the button to 12/24 RIGHT
enter the Hour mode, when the figure indicating
HOUR LEFT starts to flash, press the button to adjust
it. Continue to press the button to enter the RIGHT
Minute mode, when the figureindicating MINUTE
starts to flash, press the button to adjust. Press the button LEFT RIGHT
to confirm & press the button again to switch to mode. RIGHT ODO
Instruction Manual
NOOFF
Open
Close
Coi n
Notice
Pass bicycle spokes through
the plastic hole on the bottom
of the magnet and tighten to
secure
The magnet is designed for spokes
that are less than 2mm thick
Specyfikacje produktu
| Marka: | Sunding |
| Kategoria: | komputer rowerowy |
| Model: | SD-576B |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Sunding SD-576B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje komputer rowerowy Sunding
22 Września 2024
22 Września 2024
21 Września 2024
21 Września 2024
20 Września 2024
20 Września 2024
20 Września 2024
20 Września 2024
18 Września 2024
18 Września 2024
Instrukcje komputer rowerowy
- Decathlon
- Bafang
- Van Rysel
- Bosch
- Blackburn
- Navman
- Kogan
- Planetbike
- O-Synce
- Sigma Sport
- Batavus
- Cresta
- Wahoo Fitness
- Powertap
- Osynce
Najnowsze instrukcje dla komputer rowerowy
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
7 Kwietnia 2025
7 Kwietnia 2025
7 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025