Instrukcja obsługi Vango Velocity 200
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Vango Velocity 200 (1 stron) w kategorii namiot. Ta instrukcja była pomocna dla 68 osób i została oceniona przez 34.5 użytkowników na średnio 4.7 gwiazdek
Strona 1/1
IF YOU HAVE ANY PROBLEMS PLEASE CONTACT YOUR LOCAL RETAILER or
AMG Group Ltd., Kelburn Business Park, Port Glasgow, Scotland. PA14 6TD.
UK Consumer Hotline: 0844 811 0535 E-Mail: info@vango.co.uk
Calls to our Customer Hotline cost 5p per minute. Calls from mobile phones, cable networks or public payphones will generally cost more.
INNER ATTACHMENT
• Open out inner tents inside ysheet and position
doorway to correspond with the living area.
• Starting from the rear corners of the tent, attach the
hooks on the inner groundsheet to
corresponding rings on the tent groundsheet.
• Suspend the inner by attaching toggles of inner tent
through rings on inside of ysheet. Do the rear rst
and work forward.
TENSION BAND SYSTEM
• When required, remove Tension Band System from
pockets and clip into the buckles in the ceiling of the
tent.
• Adjust the straps until they are taut but do not over-
tension.
TO DEFLATE THE AIRBEAM TENT
• Unscrew the valve fully from the beam, taking care as the
valve will be under pressure from the air inside the tube.
IN THE UNLIKELY EVENT OF A PUNCTURE
• Note: Most apparent punctures are a result of the valve
not being screwed in correctly. Please check valves
before changing AirBeam tube.
• eate the AirBeam. Unzip the internal ysheet sleeve D
which contains the aected beam.
• Remove the tube and its protective outer.
• The zips for the protective outer are cable tied together
to prevent accidental access. Cut the cable tie and open
the zip. DO NOT open these zips when tube is inated.
• Remove the clear rubberised tube from the protective
sleeve taking care when removing the valve from the
sleeve.
• Partially inate the tube and pass through a bucket or
basin of water, looking for air bubbles. This will indicate
location of puncture.
• Use the repair patch provided and cover hole, using
instructions on patch. Re-insert tube into protective
outer, closing zip from both ends, so that zip pullers are
in the centre of the sleeve, and then replace into the
ysheet sleeve. (This may be easier with the tube
partially inated)
FLYSHEET FIRST PITCHING/COMBINED PITCHING
• Unpack and position the tent in the required direction.
• Peg out the 4 corners using the pegs supplied.
• Locate inating points at the base of each beam.
• Access the beams through the zipped entry points and
through the side door.
• For the rst use of the tent, fully unscrew all valves from
the AirBeams and screw back in carefully - this ensures
that the valve is not cross-threaded.
• Remove smaller screw-cap on valve and insert largest
pump nozzle of the Vango AirBeam™ pump supplied.
• Inate all tubes to 7psi. The tubes MUST be guided into
an arch as they are inated.
• Final tube pressure MUST NOT exceed 8psi.
DO NOT OVER-INFLATE THE BEAMS
• Start with the centre tube and guide the beam into an
upright position while it is inating.
• Inate the other beams.
• Remove pump and tighten screw-cap. Ensure both parts
of valve are well tted so it is air tight but do not over
tighten.
• Ensure the tent is in a straight line. The groundsheet
should be at and wrinkle free.
• Secure the tent by pegging out the sides using all the
pegging points available.
• Peg out ALL the guy lines, ensuring that they are in line
with the beam or seam they are attached to.
• Re-position and adjust tensioning where necessary.
CORRECT PUMP SETUP
Pump Body -> Pressure Valve -> Pressure Gauge -> Hose
(Ensure Valve/Gauge/Hose are connected to Ination
port of pump)
CORRECT AIRBEAM VALVE SETUP
Ination Deation
Velocity
Specyfikacje produktu
| Marka: | Vango |
| Kategoria: | namiot |
| Model: | Velocity 200 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Vango Velocity 200, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje namiot Vango
30 Marca 2025
28 Grudnia 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
1 Października 2024
29 Września 2024
Instrukcje namiot
- Thule
- OZtrail
- Mountain Hardwear
- Step2
- Babymoov
- Wilderness Equipment
- Wynnster
- Vrijbuiter
- TOOLPORT
- Grand Canyon
- Thermex
- Perel
- Robens
- Fiamma
- MSR
Najnowsze instrukcje dla namiot
31 Marca 2025
29 Marca 2025
29 Marca 2025
29 Marca 2025
29 Marca 2025
29 Marca 2025
29 Marca 2025
29 Marca 2025
28 Marca 2025
26 Marca 2025