Instrukcja obsługi Yamaha VXH8W
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Yamaha VXH8W (9 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 5.5 użytkowników na średnio 4.4 gwiazdek
Strona 1/9
1
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe place for future reference.
This product is a hanging pendant speaker. Do not use for any purposes other than the one intended. Those who are unfamiliar with
handling or those who can not handle according to this manual, should be supervised by responsible persons to ensure safety. Always
consult a professional installer if the product installation requires construction work.
WARNING
Always follow the basic precautions listed
below to avoid the possibility of serious
injury or even death from electrical shock,
short-circuiting, damages, fire or other
hazards. These precautions include, but
are not limited to, the following:
If you notice any abnormality
• If any of the following problems occur,
immediately turn off the power of the amplifier.
- Unusual smells or smoke are emitted.
- Some object, or water has been dropped
into the product.
- There is a sudden loss of sound during use
of the product.
- Cracks or other visible damage appear on
the product.
Then have the product inspected or repaired
by qualified Yamaha service personnel.
Do not open
• This product contains no user-serviceable
parts. Do not attempt to disassemble the
internal parts or modify them in any way.
Water warning
• Do not use the product in humid places. This
product has IPX5 compliant waterproof
performance and can be used outdoors.
However, avoid a humid environment where
water droplets such as condensation may form
inside the product. If liquid such as water gets
inside, it may cause electric shock, fire, or
malfunction.
• The speaker hanging bracket Gripple Kit
cannot be used outdoors. It also cannot be
used indoors in places where it may get wet or
be splashed with water. The metal fittings may
rust and the speaker may fall, resulting in injury.
When using in such a place, make sure to use
other suitable general-purpose metal fittings.
Fire warning
• Do not place any burning items or open flames
near the product, since they may cause a fire.
Hearing loss
• Before turning the power of the amplifier on or
off, make sure that all volume levels are set to
the minimum. Failing to do so may result in
hearing loss, electric shock, or device
damage.
• When turning on the AC power in your audio
system, always turn on the power amplifier
LAST, to avoid hearing loss and speaker
damage. When turning the power off, the
power amplifier should be turned off FIRST for
the same reason.
Location and connection
• It is the responsibility of the installer to use a
support system which has sufficient wind load
strength to comply with the applicable codes
and standards.
• Do not install the product in an unstable
position or a location with excessive vibration,
where it might accidentally fall down and cause
injury.
• Assemble and install in the manner instructed
in the manual. Falling may result in injury or
damage.
• Always consult a professional installer if the
product installation requires construction work,
and make sure to observe the following
precautions.
- Choose mounting hardware and an
installation location that can support the
weight of the product.
- Attach the two wires as described in this
manual.
- Avoid locations that are exposed to constant
vibration.
- Use the required tools to install the product.
- Inspect the product periodically.
Improper installation can cause accidents and
serious injuries.
Handling caution
• Confirm that the finished installation is safe and
secure. Also, carry out safety inspections
periodically. Failure to observe this may cause
devices to fall and result in injury.
CAUTION
Always follow the basic precautions listed
below to avoid the possibility of physical
injury to you or others. These precautions
include, but are not limited to, the
following:
Location and connection
• Keep this product out of reach of children. This
product is not suitable for use in locations
where children are likely to be present.
• Do not place the product in a location where it
may come into contact with corrosive gases or
salt air. Doing so may result in malfunction.
• Do not use the speaker’s carrying band for
suspended installation. Doing so can result in
damage or injury.
• Use only speaker cables for connecting
speakers to the speaker jacks. Use of other
types of cables may result in fire.
Handling caution
• Do not insert your fingers or hands in any gaps
or openings on the product (ports.).
• Do not rest your weight on the product or place
heavy objects on it.
• When choosing a power amplifier for use with
this product, make sure that the output power
of the amplifier meets the following conditions:
- When using a low-impedance connection,
make sure that the output power of the
amplifier is lower than the power capacity of
this product.
- When using a high-impedance connection,
be sure that the total rating of the transformer
taps of the speakers does not exceed the
output power of the amplifier.
If the output power is not appropriate,
malfunction or fire may occur.
• Do not input excessively loud signals that may
result in clipping in the amplifier or cause the
following:
- Feedback, when using a microphone
- Continuous and extremely loud sound from a
musical instrument, etc.
- Continuous and excessively loud distorted
sound
- Noise caused by plugging/unplugging the
cable while the amplifier is turned on
Even if the output power of the amplifier is
lower than the power capacity of this product
(program), damage to the product,
malfunction or fire may occur.
(PA_en_12)
General Specifications
*1: Full-space (4π)
*2: Calculated based on power rating and sensitivity
The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest
manual, access the Yamaha website then download the manual file. The dimensions are shown in
“Dimensions” on the back side of the manual.
Model
VXH6B, VXH6W VXH8B, VXH8W
System Type
Coaxial 2 way, Bass reflex type
Component
LF: 16 cm Cone
HF: 2.5 cm Soft Dome
LF: 20 cm Cone
HF: 2.5 cm Soft Dome
Frequency Response
*1
(-10 dB)
55 Hz – 20 kHz 57 Hz – 20 kHz
Coverage Angle
*1
120° 75°
Crossover Frequency
3 kHz
Nominal Impedance
8 ohm
Transformer
Taps
70 V
60/30/15/7.5 W
100 V
60/30/15 W
Power rating
NOISE
75 W 90 W
PGM
150 W 180 W
MAX
300 W 360 W
Sensitivity
*1
(1 W, 1 m)
93 dB 94 dB
Maximum SPL
*2
(Calculated, 1m, Peak)
118 dB 120 dB
Dimension
⌀ ⌀341 × H 379 356 × H 434
Weight
5.7 kg 7.2 kg
Connector
Euroblock (4 pin) × 1 (input: +/-, loop-thru: +/-)
Min. wire size AWG 24 (0.2 sq)
Max. wire size AWG 12 (3.5 sq)
Protection
Full-range power limiting to protect network and transducers
Enclosure Finish
VXH6B Black painting
(approximate value: Munsell N3)
VXH6W White painting
(approximate value: Munsell N9)
VXH8B Black painting
(approximate value: Munsell N3)
VXH8W White painting
(approximate value: Munsell N9)
Grille Finish
VXH6B Black powder coating
(approximate value: Munsell N3)
VXH6W White powder coating
(approximate value: Munsell N9.3)
VXH8B Black powder coating
(approximate value: Munsell N3)
VXH8W White powder coating
(approximate value: Munsell N9.3)
Water and Dust proof
IP45 (when waterproofing the cover hole)
Packaging
1 pc / packaging
Included Accessories
Gripple Kit × 1
Euro Block (4 pin) × 1
Cushion Seal × 1
Back Cover Set × 1
Owner’s Manual × 1
GRIPPLE Kit Installation Guide × 1
Suitable for installation with NFPA 70, National Electrical Code
Before hanging the speaker from the ceiling structure, ensure that the
strength of the ceiling structure is sufficient.
Pre-installation (Preparation of the Cable)
For cables attached to the Euroblock plug, strip the insulation as shown in
the figure and connect them.
1. Thread the two included wires through the hole in the back cover.
2. Thread the wire through one of the oval holes on both the left and right
sides of the Gripple fastener.
3. Hang the threaded wire through the ceiling structure and thread it
through the oval hole on the other side of the Gripple fastener.
4. Snap the hook onto the center hole in the hanger bracket on the back of
the speaker.
5. Adjust the position (height) of the speaker. To raise it, pull the cable
further forward. To lower it, hold the speaker so that it does not fall, and
insert the setting key into the small hole on the left and right sides of the
Gripple fastener that you want to release, and press it. The wire in the
oval hole on the plugged side is unlocked, allowing the wire to move in
the opposite direction and lowering the speaker position.
6. Secure the second wire to a sturdy structure that is different from the
structure you wired in step 3, using the same procedure as for the first
wire. Snap the hook onto either the left or right hole of the hanger
bracket on the back of the speaker. After adjusting the height, cut off the
excess wire.
Installing the Speaker
NOTICE
When installing the speakers, turn off the power amplifier.
NOTE
The example illustrations in this manual are of the VXH6B.
NOTE
Do not plate core wires by soldering if the cable uses stranded wire.
Doing so will cause the wire to break.
Suspend the Speaker
WARNING
• The direction in which the wire is passed is fixed. If you
pass it through the wrong hole or direction, the wire will fall
off and the speaker will fall.
• Be sure to use the included wire.
About 7 mm
Compatible cable:
Min. AWG24 (0.2 sq)
Max. AWG12 (3.5 sq)
1
Back cover
Wire
Gripple
fastener
WARNING
Insert the setting key into the correct hole. If you insert in the
wrong place, the wire may fall off and the speaker may fall,
resulting in serious injury.
Setting key
To raise To lower
1. Thread the speaker cable from the power amplifier through the back
cover.
2. After loosening the terminal screws of the Euroblock plug with a flat-
blade screwdriver, insert the cable into each terminal and tighten the
screws.
Use a flat-blade screwdriver with a blade less than 3 mm.
3. Plug the connected Euroblock plug into the socket in the speaker.
1. Select the line voltage/impedance (100 V, 70 V, 8 Ω) and power tap for
a 100 V, 70 V line distributed system, by rotating the tap selector switch
on the back side of the speaker with a flat-blade screwdriver. When
using the speaker with high-impedance connection, select the position
where wattage is indicated by the line (100 V, 70 V). Do not select the
“×” setting when connecting to a 100 V line. When using it with low
impedance connection, select the 8 Ω position.
2. Attach the back cover with the included screws.
Connect the Wiring to the Connector
2
Terminal screw
Loosen
Flat-blade screwdriver
Euroblock plug
Tighten
From amplifier or
previous speakers
To subsequent
speakers
Less than 3 mm
Set the Line Voltage/Impedance and Power
NOTICE
Make sure the amplifier is switched off before operating the tap selector
switch. If the setting is incorrect, it may cause malfunction of the
speaker and amplifier.
WARNING
Confirm that the finished installation is safe and secure by
shaking or pulling lightly.
If not installed securely, it can fall and cause injury.
NOTICE
(The following installation is not evaluated by UL.)
• When using outdoors, fill the hole in the center of the cover with a
cushion seal, pass the speaker cable through the notch and the
support wire through the slit, and then fill the gap with an compatible
sealant (*) to prevent water from entering.
• The Gripple kit cannot be used outdoors. It also cannot be used
indoors in places where it may get wet or be splashed with water. If
you want to use the speaker in such a place, make sure to use other
general-purpose metal fittings (*).
* An outdoor compatible sealant and general-purpose metal fittings are not
included. Please use appropriate materials in consideration of the
installation situation.
3
The illustration indicates the setting at
60 W for a 100 V line and 30 W for a 70 V line.
Cushion seal
Support
wires
Speaker cables
Example when
using max. of 4
In use
Notch Slit
SPEAKER SYSTEM
VXH8B VXH8W VXH6B VXH6W
Owner’s Manual
EN
English
VFU7330
• Protection Circuit
This speaker system has an internal protection circuit that shuts off
the speaker unit when an excessive input signal is applied. If the
speaker unit emits no sound, reduce the volume level of the
amplifier immediately. (The sound will return automatically in several
seconds.)
• Air blowing out of the bass reflex ports is normal, and often occurs
when the speaker is handling program material with heavy bass
content.
NOTICE
To avoid the possibility of malfunction/damage to
the product or damage to other property, follow
the notices below.
Handling and maintenance
• Do not expose the product to excessive dust or
vibration, or extreme cold or heat, in order to
prevent the possibility of panel disfiguration,
unstable operation, or damage to the internal
components.
• Be sure to observe the amplifier’s rated load
impedance, particularly when connecting
speakers in parallel at low impedance.
Connecting an impedance load outside the
amplifier’s rated range can damage the
amplifier.
• When using a high-impedance speaker
connection, make sure the audio signal is
passed through an 60 Hz or above high-pass
filter before being input to the speakers.
• Do not touch the speaker driver unit, since it
might cause malfunction.
• When placing the grill face down on the
ground, always place it on a flat surface with
the protective sheet attached.
• Do not place vinyl, plastic or rubber objects on
the product, since this might cause alteration
or discoloration of the panel.
• When cleaning the product, use a dry and soft
cloth. Do not use paint thinners, solvents,
cleaning fluids, or chemical-impregnated
wiping cloths, since this might cause alteration
or discoloration.
Information
About this manual
• The illustrations as shown in this manual are for
instructional purposes only.
• The company names and product names in
this manual are the trademarks or registered
trademarks of their respective companies.
About disposal
• This product contains recyclable components.
When disposing of this product, please contact
the appropriate local authorities.
Yamaha cannot be held responsible for
damage caused by improper use or
modifications to the product.
Unpacking
Unpack the contents and confirm that all the following items are included.
• Speaker × 1
• Gripple Kit × 1 (Gripple Fastener × 2, Wire (About 6 m) × 2, Setting Key × 1)
A kit for hanging the speaker. The usage and safety precautions are explained in the attached
“GRIPPLE Kit Installation Guide.” Please be sure to read before use.
• Back Cover Set × 1
• Euro Block × 1
• Cushion Seal × 1
• Owner’s Manual (this manual) × 1
• GRIPPLE Kit Installation Guide × 1
* Speaker cable is not included.
Specyfikacje produktu
| Marka: | Yamaha |
| Kategoria: | głośnik |
| Model: | VXH8W |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Yamaha VXH8W, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje głośnik Yamaha
5 Lutego 2025
15 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
9 Stycznia 2025
9 Stycznia 2025
9 Stycznia 2025
9 Stycznia 2025
9 Stycznia 2025
9 Stycznia 2025
Instrukcje głośnik
- Nokia
- REL Acoustics
- GPO
- Maginon
- Caliber
- Edifier
- Exibel
- Trettitre
- Salora
- Furuno
- NAD
- Urban Revolt
- Wharfedale
- 2N
- Taga Harmony
Najnowsze instrukcje dla głośnik
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
7 Kwietnia 2025
7 Kwietnia 2025
7 Kwietnia 2025
5 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025