Instrukcja obsługi Accell UltraAV K078C-008B
Accell
przedłużacz AV
UltraAV K078C-008B
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Accell UltraAV K078C-008B (2 stron) w kategorii przedłużacz AV. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 6 użytkowników na średnio 4.6 gwiazdek
Strona 1/2
Model Number:
K078C-008B
UltraAV®
HDMI Splitter and Distribution
Amplifier with HDBaseT Lite
READ ME FIRST – SETUP INSTRUCTIONS
Thank you for purchasing the Accell UltraAV HDMI
Distribution Amplifi er. This product is designed to provide
an exceptional performance and lue. Please review the va
manual before operating and retain for future reference.
- CAUTION -
1. Ensure the unit has suffi cient
ventilation. Do not cover
ventilation openings. Do not install
in a confi ned space.
2. Do not operate near source
of heat. Do not stack on to p,
underneath or between other heat
generating unit/s including other
amplifi ers.
3. Unplug power adapter if not
used for an extended period.
4. prevent damage from power To
surges, the unit should be plugged
into a surge protector or surge pro-
tected power source.
5. Do not use near liquid or areas
of heavy moisture.
6. Clean unit with a clean and dry
cloth only.
7. This unit cannot be serviced in
the fi eld. Contact Accell if service is
required.
8. Do not open case, risk of shock -
shock hazard.
9. Do not modify power cord or use
the product if the power cord is
damaged.
Introduction
The UltraAV HDMI Distribution Amplifier (Splitter) featuring HDBaseT
Lite accepts a signal from a single HDMI enabled audio/video source and
splits the single input into 4 HDMI outputs. The audio/video signal is
mirrored on up to 4 HDMI displays, monitors, projectors or TV’s.
Over-Current and Over-Voltage Protection
The circuit boards are equipped with both oltage over-current and over-v
protection and will automatically power down if encountered. The circuit
boards will restore automatically once the ex ltage cessive current or vo
has passed.
Package Contents
●HDMI Distribution Amplifier (Splitter) ●1 Power Adapter (for Matrix)
●4 HDBaseT Receivers ●4 Power Adapters (for ceivers)Re
●Owners Manual ●4-Pair IR-TX and IR-RX
1x4 HDMI Splitter with HDBaseT Lite
Model: K078C-008B
Specifi cations
● Connect 1 HDMI Source to up to 4 HDMI Displays
● Supports HD resolutions up to 1080P and 3D
● HDMI 1.4a, HDCP 1.2 compliant
● Data transfer speed of 6.75Gbps (225MHz)
● Audio formats supported: DTS-HD 7.1, Dolby True-HD 7.1
● Deep color up to 36-bit
● Maximum HDMI input/output cable length: Up to 16ft./5m
● Maximum Cat5e/6 output cable length: Up to 230ft./70m
● Shelf or surface mountable
● 9V DC, UL Listed Power Supply for 1x4 Splitter Unit
● 5V DC, UL Listed Power Supplies for Receiver Units (4 tal)To
● Input AC: 50Hz to 60Hz, 100-240V
● Splitter dimensions: 10.9”W x 1.1”H x 6.1”D (277W x 28H x 156D mm)
Setup
Note: All Cat5e/6 cables must be terminated to 568B standards.
Unsheilded (or properly terminated sheilded cable), solid core Cat5e,
Cat6, Cat6e, Cat7 or Cat7e cable can be used. Stranded core is not
suggested as it can reduce signal transfer. Recommended to use a
continuous length of cable terminated at the matrix and receiver ends.
With the splitter power switch in the OFF position, connect the HDMI
High Speed cable from the HDMI Output of the audio/video source to the
HDMI Input located on the rear of the splitte r.
Tips: Use the shortest length HDMI cables possible in each point
in the installation. Use only High Quality and High Speed HDMI
cables.
Next, connect a Cat5e/6 cable to the HDBaseT Out 1 port on the rear of
the splitte Connect the other end of the Cat5e/6 cable to the HDBaseT r.
IN port on the rear of the HDBaseT receiver positioned near the TV. Run
a short, High Speed HDMI cable from the HDMI Out port on the receiver
to the HDMI In port on the TV. Plug a provided power adapter into an
AC outlet and the other end into the HDBaseT receiver. Using the same
steps, connect the remaining displays to the splitter.
Important: The HDBaseT Receivers when operating are rm and do wa
require space around the housing for air circulation and coollng. Do not
enclose the HDBaseT receiver. If placed behind a component such as a
TV, ensure that there is adequate space for air circulation and ambient
cooling that there is no heat being generated and transmitted to the and
receiver from the other device. Damage caused improper placement by
and overheating of the splitter or the receiver is not covered by the
product warrant y.
On initial power on, all LED lights on the splitter should come on solid
blue. If less than the maximum number of Displays are connected to
the splitter (not all the outputs are used) there will be no corresponding
HDMI OUT blue LED for the unused output. Blue lights will only appear
for devices connected.
The HDBaseT Receiver has 4 LED indicators:
1. HDCP: A solid LED indicates that the HDCP handshake between the
source and displ has been authenticated.ay
2. Link: Indicates a connection between the Matrix and the Receiver.
3. Mode: A flashing LED indicates correct operation of the system.
4. Power: A solid LED indicates power to the receiver.
LED Indicator Lights
specifications continued:
● Receiver dimensions: 4.4” W x .9” H x 3” D (112W x 23H x 76D mm)
● Operating temperature range: 5 to 131°F (-15 to 55°C)
● Operating humidity range: 5% to 90% RH (no condensation)
Specyfikacje produktu
| Marka: | Accell |
| Kategoria: | przedłużacz AV |
| Model: | UltraAV K078C-008B |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Accell UltraAV K078C-008B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje przedłużacz AV Accell
10 Września 2024
9 Września 2024
Instrukcje przedłużacz AV
- Dune
- Marshall Electronics
- Monacor
- Oehlbach
- Trevi
- Alfatron
- ATen
- Edimax
- Enson
- Peerless-AV
- Provision ISR
- Bogen
- DVDO
- PureTools
- SIIG
Najnowsze instrukcje dla przedłużacz AV
8 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
26 Lutego 2025
20 Lutego 2025
20 Lutego 2025
7 Lutego 2025