Instrukcja obsługi Acctim Murren Radio Controlled Alarm Clock
Acctim
budzik radiowy
Murren Radio Controlled Alarm Clock
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Acctim Murren Radio Controlled Alarm Clock (1 stron) w kategorii budzik radiowy. Ta instrukcja była pomocna dla 19 osób i została oceniona przez 10 użytkowników na średnio 4.8 gwiazdek
Strona 1/1
TO INSTALL/REPLACE BATTERIES
Open the battery compartment cover and insert the batteries observing the
polarity markings inside the compartment. All segments will display briefly and the
clock display will show 12:00. The clock will automatically search for the time signal
and the Radio signal icon ' ' will flash.
If the clock receives the time signal it will set automatically within 10 minutes and
the Radio signal icon will remain on the display.
If the clock does not receive the time signal it can be set manually.
Thank you for your purchase of this quality clock. Please read these instructions
carefully and store them in a safe place for future reference.
INTRODUCTION
The Radio Controlled Mechanism fitted to your clock has a built in receiver which
is tuned into the National Physical Laboratory MSF transmitter based in Anthorn,
Cumbria, UK.
The advantages of using this Technology are:
1. Automatically adjusts the clock for Summer/Winter time changes.
2. Automatic precision.
3. Fully Automatic set up - Simply insert batteries.
GB
TO SET THE CLOCK MANUALLY - When the radio signal icon is flashing,
press DOWN/RCC button to stop and remove the icon before setting.
Press and hold TIME/SET button for 2 seconds and the 12/24 hour will start to flash.
press UP or DOWN button to to select between 12/24 hour format.
.
Press TIME/SET buttononce again, the time zone digit ‘0’ (for UK time zone) will
Press TIME/SET button once again, the time digits change to year '2017' and flash.
Press UP or DOWN button to set the year.
Press TIME/SET button once again, month digits will flash. Press UP or DOWN
button to set the month.
Press TIME/SET button once again, date digits will flash. Press UP or DOWN
button to set date.
Press TIME/SET button once again,°C will flash. To select temperature in degree °F,
press UP or DOWN button to set.
Press TIME/SET button once to complete, or let it exit automatically 10 seconds later
without pressing any key.
The following suggestion may help improve reception of the MSF signal:
Check that the batteries are new and in good condition.
Check that the batteries are inserted correctly.
Try rotating the clock as the internal receiver that picks up the signal is
most effective when it is facing directly towards or away from Anthorn.
CHANGING THE BATTERIES AND MAINTENANCE
It is recommended that you replace the batteries annually even if the product is
still running. Only use 2 X AAA (1.5V) Alkaline batteries in this clock. Do not mix
new or used batteries, different types or brands. Remove the batteries if the clock
is stored or not in use. Remove exhausted batteries from the product.
Warning: Do not recharge non-rechargeable batteries.
Please dispose of used batteries in a responsible manner. For more information
please contact your local authority.
A soft cloth may be used to clean your clock. Do not use any corrosive cleaner or
chemical solutions on the clock. Keep the clock clean and dry to avoid any
problems.
YOUR GUARANTEE
Your clock is guaranteed for 12 months from the date of purchase against any
faults arising from defective materials or manufacture. Damage caused through
careless handling, misuse or in transit is expressly excluded. Should this clock fail
within 12 months please return it in the first instance to your retailer.
If you have any queries, problems or do not understand any
part of these instructions please contact:
Customer Help Line (01908) 449208 Mon - Fri 9.00am - 4.30pm
email for service: service@acctim.com or visit www.acctim.com
Environmental Protection
Disposal of electrical & electronic equipment
Do not dispose of this product with household waste. For the proper
treatment, recovery and recycling please take this product to the
appropriate collection point. If you are unsure of where this is contact your
local authority. Improper disposal may be harmful to the environment.
V..1
MSF RECEPTION DIFFICULTIES
Like any receiver your clock needs a good signal to work properly. The main
causes of reception failure are...
Atmospheric and local interferences.
Interference from electrical equipment e.g. TV, computers or radios.
Location of the clocks internal receiver within the building.
Reduced local signal due to steel framed structure.
Outside the normal transmission.
Try moving your clock to a new location away from any electrical equipment e.g.
TV, computer or radios, and start the set up again or remove the batteries and
insert again after 5.30pm. Due to local interference the signal is stronger between
midnight & 5am.
MORITZ RC LCD ALARM CLOCK
SNOOZE/LIGHT
Touch SNOOZE/LIGHT button to light the display for a few seconds.
Touch SNOOZE/LIGHT button to activate snooze during alarm, after which
the alarm
the snooze time.
will sound again approximately 5 minutes later. (Zz) icon will flash during .
DAYLIGHT SAVING TIME
Your clock will automatically adjust to the Summer/Winter time changes. Summer
time starts on the last Sunday in March and ends on the last Sunday in October.
The summer time icon ‘DST’ will automatically appear above the display to indicate
summer time.
TO VIEW ALARM 1 AND 2 TIME
At normal time display, press DOWN/RCC button.
Note: The clock will automatically search for the time signal everyday at 1:00,
.
2:00 and 3:00am. If it fails to receive the time signal by 3:00am, it will search again
at 4:00am and 5:00am. If the signal is weak and your clock does not set, move
your clock to a new location, press and hold DOWN/RCC button for 3 seconds
to start the radio controlled signal search.
Interruption to the MSF signal
The Anthorn transmitter is periodically shut down for scheduled maintenance
resulting in no signal being transmitted. For dates of the schedule maintenance visit
http://www.npl.co.uk/science-technology/time-frequency/products-and-services/
time/msf-outages or call the NPL MSF recorded message on (0)20 8943 6493.
flash. If you would like your clock to display a different time zone (e.g. location
abroad), find out how many hours ahead/behind the time zone is. Press UP or
DOWN button to adjust to the correct hour for the time zone.
Press TIME/SET button once again, the hour digits will flash. Press UP or DOWN
button to set the hour (In 12 hour format set AM and PM time correctly).
Press TIME/SET button once again, the minute digits will flash. Press UP or
DOWN button to set the minute.
Press TIME/SET button once again, the seconds digits will flash. Press UP or
DOWN button to set the seconds.
Press TIME/SET button once again and the language for day of the week will flash.
Press UP or DOWN button to select the language for day of the week.
Languages available English (ENG), German (GER), French (FRA), Spanish (ESP),
Italian (ITA).
BATTERY COMPARTMENT
INSERT 2 x AAA BATTERIES
Front view
SETTING ALARM1 / ALARM2
1. Press and hold AL/SET button, the time display will change to Alarm1 digits
and hour digits will flash.
2. Press UP or DOWN button to set the alarm hour (In 12 hour format set AM
and PM time correctly).
3. Press AL/SET button once again, the minute digits will flash, press UP or
DOWN button to set the alarm minute.
4. Press AL/SET button once to confirm and move to Alarm2 setting, hour digits will
flash. Repeat step 2 and 3 above to set ALARM 2.
5. Press AL/SET button once to complete.
TO TURN ON/OFF THE ALARM 1 AND 2
1. At normal time display, press AL/SET button once to activate Alarm1.
The alarm1 symbol will appear on the display.
2. Press the AL/SET button once again to activate Alarm2. The alarm2 symbol
will appear on the display.
3. Press the AL/SET button once again to activate both Alarm 1 and 2.
Both alarm 1 and 2 symbols and will appear on the display.
4. Press the AL/SET button once again to deactivate both alarms. Both alarm 1
and 2 symbols and will disappear.
When the alarm 1 or 2 activates press any button (except SNOOZE/LIGHT) once
to turn off the alarm, the alarm will activate at the same time the next day.
Please note. If your second alarm activates while the first alarm is sounding
or it is in the snooze mode, the second alarm will override the first alarm (the first
alarm will reset and sound again on the next day).
Back view
SNOOZE/LIGHT
TIME/SET AL/SET UP DOWN/RCC
Specyfikacje produktu
| Marka: | Acctim |
| Kategoria: | budzik radiowy |
| Model: | Murren Radio Controlled Alarm Clock |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Acctim Murren Radio Controlled Alarm Clock, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje budzik radiowy Acctim
8 Kwietnia 2025
3 Lutego 2025
Instrukcje budzik radiowy
- Caliber
- Adler
- Tesco
- Lexon
- Brandt
- Medion
- Renkforce
- Vitek
- Ices
- Hama
- Sencor
- Muse
- Hyundai
- Krontaler
- Timex
Najnowsze instrukcje dla budzik radiowy
9 Kwietnia 2025
9 Kwietnia 2025
7 Kwietnia 2025
7 Kwietnia 2025
6 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025