Instrukcja obsługi AMX DXFP-TX-4K60
AMX
nieskategoryzowany
DXFP-TX-4K60
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AMX DXFP-TX-4K60 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 4.5 użytkowników na średnio 5.0 gwiazdek
Strona 1/2
QUICK START GUIDE
DXLink™ Fi4K60 HDMI ber Transmitter/Receiver
Mounting Options (Rack Trays and Mounting Brackets)
The DXFP-TX-4K60 and DXFP-RX-4K60 can be mounted using V Style Surface Mounting
Brackets, V Style Single Module Pole Mounting Kit, or NMX-VRK V-Style Rack Shelf.
For details, see www.amx.com
IMPORTANT: When mounting under a surface, the module should be mounted upright and
lowered in the mounting bracket slots to provide an airflow gap between the surface and
the vent holes. If not using V Style brackets, be sure to leave a gap between the top of
the unit and the surface for heat to escape.
1 2 3 4
ON
ID USB MODE
DIP Switch Toggles – Default OFF (for Auto-setup, see next page)
Before installing the units, find the scenario you are using in the table below and set the
DIP switch toggles accordingly. Toggle #4 is reserved for future functionality.
For standalone pair upgrades, set Toggles #1-2-3 to ON and connect one unit to Controller.
** In standalone setup using NetLinx control of DXLink serial R ports, only one of the /I
DXLink units should be connected to network ( e it with #1 Toggle enabled). fiber th un
COMMON SCENARIOS TOGGLES
Standalone Setup 1 - 2 - 3
AV signals only (plus serial/IR passthrough) OFF - OFF - OFF
AV ith Ethernet passthrough to networked device plus serial/IR w (
passthrough)*
ON - OFF - OFF
AV with NetLinx control of TX/RX unit and serial/IR ports** ON - N - N O O
AV with NetLinx control of TX/RX unit and serial/IR ports, plus Ethernet
passthrough to network device*
ON - N - N O O
Switcher Setup (TX/RX with Enova DGX/DGX 100 Series Switcher) 1 - 2 - 3
AV signals only OFF - OFF - OFF
AV with Ethernet passthrough to networked dev e* ON - OFF - OFFic
AV with NetLinx control of TX/RX unit and serial/IR ports OFF - OFF - ON
AV with NetLinx control of TX/RX unit and serial/IR ports, plus Ethernet
passthrough to network device*
ON - OFF - ON
•Endpoint Mode (Switcher) – connect one or more to a switcher with an integrated
•Endpoint Mode (Standalone) – connect TX/RX pair dire y to each other with onectl
connected to a inx Central Controller via LAN or directly to Controller.NetL
•Extender Mode (Standalone) – connect TX/RX pair directly to each other.
These Modules support InstaGate Pro® and SmartScale® Technology.
The contains Hardware Reference Manual - DXLink Fiber Transmitter/Receiver 4K60
complete documentation (including full specifications and supported input and output
resolutions) for details, see www.amx.com.;
System upSet
T DXFP-TX-4 nd DXFP-RX-4 ork ith tha sup DXLinkhe K60 a K60 w w a switcher t ports
Technolog or s stand-alone transmit udio, ideo nd signals. he y a a pair to a v a control T
Transmi receives ud o nd eo the source nd transmits oth udio tter a i a vid from HDMI a b a
and le. This DXLin ca irectly video over the fiber optic cab k fiber optic ble can be connected d
to DXLin eceiver or to DXLin input on DXLink switcher where it can be a k fiber ra k fiber a
routed to a DXLin output and connected to DXLin eceiver. The DXLin k fiber a k fiber rk fiber
recei er converts the DXLin input to HDMI and nalog udio outputs. On the v k fiber a a
transmitter, stereo e ov edaudio connections ar pr id as sup lemental input. the a p audio Both
t rransmitter the and eceiver sup ort -2 or serial ta transfer, IR, Ethernet.p RS 32 f da USB, and
FI . 1 G DIP WITCH S TOGGLES ENABLE/DISABLE ECIAL UNCTIONALITYSP F
Ov viewer
The DXFP-TX-4K60 and DXFP-RX-4K60 transmit HDMI, audio, USB and control over
fiber optic cable The TX also has an HDMI loop out. DXLink ber odules can be set . fi m
up in one of three ways:
FIG. 3
HDMI IN
Fiber optic cable
HDMI OUT
Source Device Destination Device
DXLINK FIBER TX AND RX AS EXTENDER SOLUTION
FIG. 2
DXLINK Fiber Transmitter
DXLINK Fiber Receiver
HDMI IN Fiber optic cable
Fiber optic cable HDMI OUT
Destination Device
DXLINK Fiber
Output Board
LAN 100/1000
Source Device
AC
DC
FLT
AC
DC
FLT
DXLINK Fiber
Input Board
DXLINK FIBER TX AND RX AS ENDPOINTS WITH COMPATIBLE DXLINK FIBER EQUIPMENT
F
IG. 4
ICS LAN 10/100 Port
The ICS LAN 10/100 port uses twisted pair cable. FIG. 4 shows the LEDs for this port.
ICS LAN (RJ45) PORT
On - Speed status is 100 Mbps
Off - Speed status is 10 Mbps
Yellow LED:
On - Link status is active
Off - Link status is not active
Green LED:
FIG. 5 FIBER OPTIC TRANSCEIVER MARKED BLACK (MULTIMODE)
Latch and/or label color
Dust g plu
SFP+ = enhance small form-factord
pluggable optic transceiver ratedfiber
at 0 s transmission ta rate. 1 Gbp da
Fiber Optic Transceivers
The DXLink Fiber Transmitters and Receivers use SFP+ fiber optic transceivers. Fiber
optic transceivers are self-contained modules that send and receive optical signals over
fiber cable. DXLink SFP+ fiber optic transceivers is multimode and must be wired with
the corresponding cable type. Multimode transceivers support bidirectional and
unidirectional communication.
Attaching Signal, Transport, and Control Cables
Important Cabling Requirements and Considerations
•
•LC Duplex conforming to ANSI TIA-EIA 604-10 (FOCIS 10A)
• DXLink Fiber multimode transceivers use OM3 50/125 μm multimode fiber optic
cable type over distances of up to 984 feet (300 m)*
•Do not create a network (Ethernet) loop. A network loop is created when the
enclosure and one or more of its DXLink Fiber units connect to a common LAN.
Fiber optic cable with LC termination for snap coupling with SFP+ transceivers
* Connect ICS LAN port of DXLink fiber unit to network device (e.g., laptop, IP controlled
projector, ICSLan Device). In standalone setup, connect ICS LAN port of other DXLink
unit to network.
* Cable quality is a determining factor for the maximum length of cable runs.
WARNING：DXLink Fiber units use laser transceiver, which are Class 1 Eye Safe per
IEC 60825-1/CDRH requirements. While the Class 1 category indicates that the invisible
laser used is safe, we recommend avoiding direct eye exposure when using any optical
fiber products (See OSHA directive referenced in the “Hardware Reference Manual”).
DXLINK Fiber Transmitter DXLINK Fiber Receiver
Controller.
Specyfikacje produktu
| Marka: | AMX |
| Kategoria: | nieskategoryzowany |
| Model: | DXFP-TX-4K60 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z AMX DXFP-TX-4K60, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje nieskategoryzowany AMX
2 Sierpnia 2024
2 Sierpnia 2024
2 Sierpnia 2024
2 Sierpnia 2024
2 Sierpnia 2024
2 Sierpnia 2024
2 Sierpnia 2024
10 Lipca 2024
10 Lipca 2024
21 Czerwca 2024
Instrukcje nieskategoryzowany
- Yamaha
- Gree
- Kisag
- Glem Gas
- MySoda
- Ring
- SMART Technologies
- MyPhone
- Razor
- AEG
- Ferplast
- ABB
- Senal
- Edilkamin
- Elica
Najnowsze instrukcje dla nieskategoryzowany
28 Października 2024
28 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024