Instrukcja obsługi AMX MXA-FMK-07

AMX nieskategoryzowany MXA-FMK-07

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AMX MXA-FMK-07 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 24 osób i została oceniona przez 12.5 użytkowników na średnio 4.7 gwiazdek

Pobierz PDF

Strona 1/2

QUICK START GUIDE

MXA-FMK-07 Modero X Series® Flush Mount Kit

MXA-FMK-07

The MXA-FMK-07 Flush Mount Kit (FG5968-71) mounts the Modero X Series 7” Wall

Mount Touch Panels flush with the wall. Once installed, simply press lightly on the black

border area on both sides of the touch panel, and the spring-loaded mechanism

switches the panel between the flush position or slightly extended from the wall

surface. The extended position gives access to the panel’s Sleep/Setup button, as well

as for enhanced speaker and microphone exposure. The MXA-FMK-07 is compatible

with all Modero X Series 7” Wall Mount Touch Panels, including:

• Refer to the 95-5968-71 diagram for detailed installation dimensions.

Installation of the Flush Mount Kit

The MXA-FMK-07 Flush Mount Kit (FIG. 1) is designed to attach the panel to most

standard wall and solid surface materials. It has two locking tabs (landscape: one on

top and one on bottom; portrait: one on each side) to help lock the Flush Mount Kit to

the wall. These locking tabs are only extended AFTER the Flush Mount Kit is inserted

into the wall. Using the locking tabs is highly recommended for standard mounting

surfaces such as walls.

WARNING: When installing the Flush Mount Kit, make sure that the assembly is in the

correct position and in the correct place. Once the locking tabs are extended and

locked into place, removing the Flush Mount Kit may be diff icult without having

access to the back of the wall or causing damage to the wall.

Note: In order to guarantee a stable installation of the MXA-FMK-07, the thickness of the

wall material must be a minimum of .50 inches (1.27cm) and a maximum of .875 inches

(2.22cm). The surface should also be smooth and flat.

WARNING: The maximum recommended torque to screw in the locking tabs on the

plastic Flush Mount Kit is 5 IN-LB [56 N-CM]. Applying excessive torque while

tightening the tab screws, such as with powered screwdrivers, can strip out the

locking tabs or damage the plastic.

1. After ensuring proper placement, cut out the mounting surface, using the MXA-

FMK-07 Cutout Template (68-5968-06) as a guide (FIG. 2).

CAUTION: The cutout dimensions shown will allow the unit to pass through without any

dragging or interference. The outer phantom lines show the perimeter of the mounting

flange. If any part of the cutout extends up to or beyond that perimeter, the cut edge will

be visible after installation, or the unit could fall through the opening. A larger cutout

reduces the available surface to support the unit when mounted, so the cut should be as

close to the indicated dimensions as possible. If the cutout is too small, forcing the unit

into place could result in mechanical binding, faulty operation, or damage to the product.

Always check for a proper fit before final installation.

2. Remove the knockout at the top of the Flush Mount Kit (FIG. 3) and thread the

incoming wiring through the knockout hole. The MXA-FMK-07 has only one

knockout hole, at the top of the device (Landscape) or to the left (Portrait).

3. Thread the incoming Ethernet wiring from their terminal locations through the

surface opening and through the knockout.

4. Push the Flush Mount Kit flat into the mounting surface and secure with the

locking tabs (FIG. 4). In order to prevent damage to the touch panel, make sure

that any screws used are flush with the Flush Mount Kit, and the Flush Mount Kit

goes freely into the opening.

• MXD-701-P (FG5968-54) • MXD-700-P (FG5968-08)

• MXD-701-L (FG5968-55) • MXD-700-L (FG5968-14)

• MXD-700-P-NC (FG5968-28) • MXD-700-L-NC (FG5968-29)

FIG. 1 MXA-FMK-07, LANDSCAPE AND PORTRAIT INSTALLATIONS

PRODUCT SPECIF ICATIONS

Dimensions (HWD): 5.50” x 8.01” x 3.48” (13.97 cm x 20.33 cm x 8.85 cm)

Weight: 1.00 lbs (0.45 kg)

Included Accessories: • MXA-FMK-07 Quick Start Guide (93-5968-07)

• MXA-FMK-07 Cutout Template (68-5968-06)

Landscape Portrait

8.01” (20.33 cm)

5.50” (13.97 cm)

FIG. 2 MXA-FMK-07 CUTOUT TEMPLATE

FIG. 3 INSERTING THE MXA-FMK-07 INTO THE WALL SURFACE (LANDSCAPE)

FIG. 4 LOCKING TAB LOCATION ON THE MXA-FMK-07 (LANDSCAPE)

7.60”

5.09”

(12.94 cm)

(19.30 cm)

Perimeter

of Flush

Mount Kit

flange

Wall Surface

MXA-FMK-07

Knockout

Locking Tab

Note: The

MXA-FMK-07

has only one

knockout hole.

Locking Tab Screw

Use a screwdriver

or other flat tool

to hold the lower

edge of the back

box above the

case while snapping

down the touch panel.

Specyfikacje produktu

Marka:	AMX
Kategoria:	nieskategoryzowany
Model:	MXA-FMK-07
Kolor produktu:	Czarny
Liczba obsługiwanych wyświetlaczy:	1
Typ mocowania:	Ściana
Kompatybilność:	MXD-701-P (FG5968-54), MXD-701-L (FG5968-55), MXD-700-P (FG5968-08), MXD-700-L (FG5968-14), MXD-700-P-NC (FG5968-28), MXD-700-L-NC (FG5968-29)