Instrukcja obsługi Apart PA8250
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Apart PA8250 (6 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 5.5 użytkowników na średnio 5.0 gwiazdek
Strona 1/6
1. Power switch
Flip this switch to turn power on and off.
2. Power led
This led is lit when power is on.
3. Channel 1 – 8 level controllers
Set the ch. 1 to 8 channel level individually with these level controllers.
4. Channel 1 – 8 status leds:
Upper “limit” led lights up when the internal limiter is active.
This should not or only very sporadically happen. Turn the level controller down if this led lights up
frequently. Lower “signal/protect” led lights up green when a sufciently high signal is present at
channels 1 to 8.
This led lights up red when the internal protection circuitry is active, due to an overload or a short
circuit. When powering up the PA8250, these leds are red during a few seconds,
this is to avoid turn on plops and clicks.
The PA8250 incorporates eight independent high power ampliers in a convenient 19” enclosure.
For those who need more power, there is the possibility of bridging the channels.
This way you can congure the amplier to your needs with a push of a button.
1 3 42
1. Fuse
Replace only with a fuse of the same rating: 10 amps, slow blow.When this fuse blows often, please
contact your local dealer and have your device serviced.
2. Link switch
When pushed in, this switch allows you to link the inputs of the odd and even numbered channels
through. E.g. left input on channel 1, right input on channel 2, by pushing the 1to3/2to4 switch, the L
input on channel 1 is switched through to channel 3 and the R input on channel 2 is switched through
to channel 4.
3. Balanced inputs channel 1 to 8
Connect your balanced input sources on these Euroblock connectors.
4. Unbalanced inputs channel 1 to 8
Connect your unbalanced input sources on these cinch/RCA connectors.
Do not use balanced and unbalanced on the same channel !
5. Highpass lter switch
Push this switch to lter out unwanted rumble or low frequency sounds.
6. Stereo/mono switch
Push this switch for stereo or mono operation.
7. 2 channel/bridged switch
Push this switch to put the amplier in bridge mode: in this mode you can unite the power of two
ampliers into one more powerful amplier. In bridge mode, minimum load impedance is 8 !
Connect the speaker – terminal to the even numbered output channel’s + connector and
the speaker + terminal to the odd numbered output channel’s + terminal.
298 1
6 7 5 4
3
Specyfikacje produktu
| Marka: | Apart |
| Kategoria: | odbiornik |
| Model: | PA8250 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Apart PA8250, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje odbiornik Apart
14 Października 2024
9 Września 2024
5 Września 2024
5 Września 2024
4 Września 2024
3 Września 2024
2 Września 2024
2 Września 2024
1 Września 2024
31 Sierpnia 2024
Instrukcje odbiornik
- odbiornik Monitor Audio
- odbiornik Palsonic
- odbiornik DirecTV
- odbiornik QTX
- odbiornik Deaf Bonce
- odbiornik Aurel
- odbiornik Motorola
- odbiornik ICOM
- odbiornik Salora
- odbiornik HQ Power
- odbiornik IFM
- odbiornik Primare
- odbiornik Pioneer
- odbiornik Key Digital
- odbiornik Wet Sounds
Najnowsze instrukcje dla odbiornik
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
30 Marca 2025