Instrukcja obsługi APC BE350G-CN

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla APC BE350G-CN (2 stron) w kategorii UPS. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 4.0 gwiazdek

Safety

Specifications

Connect the Battery

The Back-UPS is shipped with one battery cable disconnected. Remove the “Stop!

Connect the Battery” label that covers the outlets. Prior to connecting any equipment

to the unit, connect the battery cable to the unused battery terminal. It is normal for

small sparks to be seen when the battery cable is connected to the battery terminal.

Wall Mount Installation

•Horizontal installation, use 2 screws 5.0" (127 mm) apart.

•Vertical installation, use 2 screws 4.3" (110.4 mm) apart.

•Allow 5/16" (8 mm), of the screw to protrude from the wall.

Connect Equipment

Battery Backup + Surge Protection Outlets

Battery backup outlets provide protection to connected equipment when the

Back-UPS is turned on and connected to utility power.

Battery backup outlets receive power from the Back-UPS for a limited period of time

when a power outage, or brownout condition occurs.

Battery backup outlets provide protection from power surges or spikes.

Connect a computer, monitor and other peripheral devices to the outlets.

Surge Protection Outlets

Surge protection outlets provide protection to connected equipment when the

Back-UPS is connected to utility power, and is switched on or off.

Surge protection outlets provide protection from power surges or spikes.

Connect a printer, scanner or other peripheral devices that do not need to remain on

during power outages, or utility problems to the surge protection outlets.

Connect Network

The Back-UPS protects equipment connected to a 10/100 Base-T ethernet, from

power surges when connected through the Back-UPS coaxial connectors.

Turn On the Back-UPS

Press the POWER ON button located on the top of the Back-UPS. The Power On/

Replace Battery LED will illuminate and a single short beep will be audible to

indicate that the Back-UPS is providing protection for connected equipment.

The Back-UPS battery charges fully during the first 16 hours while connected to

utility power. The Back-UPS battery will charge while the Back-UPS is switched on

or off and is connected to utility power. Do not expect full battery run capability

during the initial charge time.

If the red Building Wiring Fault LED located on the side of the Back-UPS

illuminates, do not operate the Back-UPS. Have a qualified electrician correct the

building wiring fault.

Voltage Sensitivity Adjustment (optional)

The Back-UPS detects and reacts to line voltage distortions by transferring to battery

backup power to protect connected equipment. In situations where either the Back-

UPS or the connected equipment is too senstage level it is itive for the input vol

necessary to adjust the transfer voltage.

1.Connect the Back-UPS to a wall outlet. The Back-UPS will be in Standby mode,

no indicators will be illuminated.

2.Press and hold the ON/OFF button for 10 seconds. The OnLine LED will

illuminate alternately green-amber-red, to indicate that the Back-UPS is in

Program mode.

3.The Power On/Replace Battery LED will flash either green, amber, or red to

indicate the current sensitivity level. Refer to the table for an explanation of the

transfer voltage sensitivity levels.

4.To select LOW sensitivity, press and hold the ON/OFF button until the LED

flashes green.

5.To select MEDIUM sensitivity, press and hold the ON/OFF button until the LED

flashes red.

6.To select HIGH sensitivity, press and hold the ON/OFF button until the LED

flashes amber.

7.To exit Program mode wait five seconds and all LED indicators will extinguish.

Program mode is no longer active.

This unit is intended for indoor use only.

Do not operate this unit in direct sunlight, in

contact with fluids, or where there is

excessive dust or humidity.

Connect the Back-UPS power cord directly to

a wall outlet. Do not use a surge protector or

an extension cord.

Input

Voltage120 VacNominal

Frequency60 Hz + 3

Brownout Transfers92 Vac Typical

Over-voltage Transfer139 Vac Typical

Output

UPS Capacity

(3 outlets)350 VA, 200 W

Total Amperage

(6 outlets)8 A (including UPS output)

Voltage - On Battery115 Vac ± 8%

Frequency - On Battery60 Hz + 1

Transfer Time6 ms Typical, 10 ms maximum

Protection

and

Filtering

AC Surge ProtectionFull time, 340 Joules

EMI/RFI FilterFull time

AC InputResettable circuit breaker

Battery

TypeSealed, maintenance-free, lead acid

Replacement battery cartridge RBC35

Average Life3 - 5 years depending on the number

of discharge cycles and environmental

temperature

Physical

Net Weight9 lb (4 kg)

Dimensions

Length x Width x Height11 in x 6 in x 3 in

29 cm x 16 cm x 9 cm

Operating Temperature32º F to 104º F (0º C to 40º C)

Storage Temperature5º F to 113º F (–15º C to 45º C)

Operating Relative Humidity0 to 95% non-condensing humidity

Operating Elevation0 to 10,000 ft (0 to 3000 m)

EMC

Compliance

This device complies with part 68 and part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) This device must accept

any interference received, including interference that may cause

undesired operation.

 Press the battery compartment cover

release tab located on the rear side of the

unit. Slide the battery cover off.

 Connect the battery cable securely to

the battery terminal.

 Reinstall the battery compartment

cover. Be sure that the release tab locks

into place.

bu064a

bu065a

bu066a

LED

Flashes

Sensitivity

Setting

Input Voltage Range

(Utility Operation)Recommended Use

GreenLOW88 Vac to 142 VacUse this setting with equipment that

is less sensitive to fluctuations in

voltage or waveform distortions.

RedMEDIUM92 Vac to 139 VacFactory default setting. Use this

setting under normal conditions.

AmberHIGH96 Vac to 136 VacUse this setting when connected

equipment is sensitive to voltage

and waveform fluctuations.

bu206a

Back-UPS

Battery Backup +

Surge Protection

Surge Protection

bu208a

CAUTION-Refer to bottom

of unit for safety markings.

Circuit

Breaker

Building

Wiring Fault

Network

Out

Push to

Reset

Network

In

User Manual Back-UPS® BE350G Series

Specyfikacje produktu