Instrukcja obsługi Atdec AWMS-DW
Atdec
Wsparcie dla paneli płaskich
AWMS-DW
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Atdec AWMS-DW (4 stron) w kategorii Wsparcie dla paneli płaskich. Ta instrukcja była pomocna dla 20 osób i została oceniona przez 10.5 użytkowników na średnio 4.9 gwiazdek
Strona 1/4
AWMS-DW Page 1 of 4
Installation Guide
AWMS-DW
Dynamic Arm Wall Mount
COMPONENT CHECKLIST
A
Single Wall
Bracket
(x1)
G
Screw
M4x25mm
(x4)
H
Screw
M4x16mm
(x4)
I
Screw
M4x12mm
(x4)
F
Spacer
(x4)
J
Security
Screw
(x1)
E
Washer
(x2)
D
Screw
M8x70mm
(x2)
K
4mm
Hex Key
(x1)
L
6mm
Hex Key
(x1)
C
VESA
Head
(x1)
B
Dynamic
Monitor Arm
(x1)
REQUIRED TOOLS
• Phillips head screwdriver
• Power drill
• Suitable drill bit
• Driver bit for selected
wall fasteners
• Stud nder
• Spirit level
WEIGHT RANGE
Flat Monitor
0 - 9kg (0 - 20lb)
Curved Monitor
0 - 6kg (0 - 13.5lbs)
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Do not remove or throw away the plastic sleeve on wall bracket and arm links.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to install this product correctly may cause serious injury/death during or following installation.
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! This product should only be installed by professional installers of good mechanical aptitude, who have experience with
building construction, and fully understand these instructions and the consequences of incorrect installation.
! Supplied wall fasteners are for timber stud wall constructions . For other wall constructions, such as masonry, alternative only
suitable wall fasteners should be sourced by the installer.
! To safely achieve the full capacity of this product, wall fasteners must have a pull-out (tension) force rating of at least 100kg
(1000N) per fastener. This rating must include a safety factor.
! Professional installer to ensure adequate structural capacity of wall (including appropriate safety factor) to support total
weight of all equipment being mounted.
! Drilling into electrical wires can cause death - use appropriate equipment and caution when drilling holes in walls to avoid
electrical cables, water pipes and gas pipes. Do not drill into structures unless you have established it’s safe to do so.
! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts),
and offset VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor
weight may be within the stated range. Please contact Atdec if you would like further information.
Specyfikacje produktu
| Marka: | Atdec |
| Kategoria: | Wsparcie dla paneli płaskich |
| Model: | AWMS-DW |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Atdec AWMS-DW, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Wsparcie dla paneli płaskich Atdec
30 Stycznia 2025
30 Stycznia 2025
30 Stycznia 2025
Instrukcje Wsparcie dla paneli płaskich
- Anywhere Cart
- Premier Mounts
- Ateca
- Erard
- StarTech.com
- XTRARM
- Peerless-AV
- Chief
- AKAI
- ViewZ
- Twelve South
- Mount-It!
- Vogel's
- Proaim
- Alogic
Najnowsze instrukcje dla Wsparcie dla paneli płaskich
8 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025