Instrukcja obsługi Audio-Technica BP892
Audio-Technica
słuchawka
BP892
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Audio-Technica BP892 (2 stron) w kategorii słuchawka. Ta instrukcja była pomocna dla 24 osób i została oceniona przez 12.5 użytkowników na średnio 4.4 gwiazdek
Strona 1/2
BP892 / BP892-TH
MicroSet® Omnidirectional Condenser Headworn Microphones
Features
BP892 Description
The BP892 is a headworn condenser microphone with an omnidirectional polar
pattern. It is designed to provide intelligible natural audio for stage and television talent,
lecturers and houses of worship.
The microphone requires 11V to 52V phantom power for operation.
The microphone includes a 1.4 m permanently attached miniature cable. Its free end
connects to the provided AT8539 power module via a locking 4-pin connector. The
connector is also compatible with all Audio-Technica UniPak® body-pack transmitters.
The output of the power module is a 3-pin XLRM-type connector.
A recessed switch in the power module permits choice of flat response or low-
frequency roll-off (via integral 80 Hz high-pass UniSteep® filter) to help control
undesired ambient noise.
The microphone comes equipped with a power module, a cable clip, a dual-ear mount,
two windscreens, two element covers, a moisture guard and a protective carrying
case. The microphone is available in black and beige.
Wireless MicroSet® Description
The microphone is also available in a variety of wireless models, including the
BP892cW. The BP892cW includes a 1.4 m permanently attached miniature cable
terminated with a locking 4-pin connector for use with Audio-Technica UniPak® body-
pack transmitters. Models are also available in a variety of terminations for use with
many other manufacturers’ wireless systems (see below). No power module or
belt clip is included (or required) with the wireless models. The wireless models’
dimensions, polar pattern and included accessories are otherwise identical to those of
the BP892.
Avoid leaving the microphone in the open sun or in areas where temperatures exceed
43° C for extended periods. Extremely high humidity should also be avoided.
Specifications
Element Fixed-charge back plate, permanently
polarized condenser
Polar pattern Omnidirectional
Frequency response 20-20,000 Hz
Low frequency roll-off 80 Hz, 18 dB/octave (wired only)
Open circuit sensitivity –49 dB (3.5 mV) re 1V at 1 Pa
Impedance 250 ohms (wired only)
Maximum input sound level 135 dB SPL, 1 kHz at 3% T.H.D.
Dynamic range (typical) 104 dB, 1 kHz at Max SPL (wired only)
Signal-to-noise radio 63 dB, 1 kHz at 1 Pa
Phantom power requirements 11-52V DC, 2 mA typical (wired only)
Current consumption 0.1 mA typical at 5V (wireless only)
Voltage range 2.5-11V (wireless only)
Switch Flat, roll-off (wired only)
Weight Microphone, boom & earpiece: 2.6 g
Power module (wired only): 85 g
Dimensions Microphone: 8.1 mm long, 2.6 mm diameter
Boom: 98.4 mm long, 1.07 mm diameter
Power module: 97.6 mm long, 18.9 mm diameter
Output connector (power module) Integral 3-pin XLRM-type
Cable 1.4 m long (permanently attached to microphone),
1.6 mm diameter, 2-conductor shielded cable with
locking 4-pin connector (wired only)
Accessories furnished AT8539 power module (wired only); AT8440
cable clip; AT8464 dual-ear mount; two AT8157
windscreens; two AT8156 element covers; moisture
guard; carrying case
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
0°
330 °
300 °
270 °
240 °
210 °
180 °
150 °
120 °
90°
60°
30°
frequency response: 20–20,000 Hz polar pattern
Frequency in Hertz
LEGEND
Response in dB
12" or more on axis
Roll-off SCALE IS 5 DECIBELS PER DIVISION
The included AT8464 Dual-Ear Microphone Mount allows you to convert your single ear-worn BP892
MicroSet ®
to a dual-ear-worn unit. The BP892 ts on either side of the Dual-Ear Microphone Mount, allowing
the microphone to be worn to either the left or right of your mouth. The headband easily adjusts to t both
children and adults.
How to use the Dual-Ear Microphone Mount
1. Insert the rounded end of your BP892 ear hook into the larger opening of your Dual-Ear Microphone
Mount’s left or right tapered holder. Firmly seat ear hook in the tapered holder.
2. Insert the small rounded end of the additional supplied ear hook into the larger opening of your Dual-Ear
Microphone Mount’s remaining tapered holder. Firmly seat ear hook in the tapered holder.
3. Open the Dual-Ear Microphone Mount’s adjustable behind-the-neck headband to its maximum position by
pushing the headband’s adjusting tabs together (a). Put the behind-the-neck headband on, hooking the ear
hooks over your ears. Adjust the t of the headband as needed, by sliding the headband’s adjusting tabs
until you arrive at a secure, comfortable t (a). Attach the microphone cable to the cable clip positioned
between the headband’s adjusting tabs (b).
1
2
3
a
b
Cable Terminations
BP892cW, BP892cW-TH – Terminated with locking 4-pin connector for use with A-T UniPak
® body-pack transmitters
BP892cL4, BP892cL4-TH – Terminated for Sennheiser
® wireless systems using Lemo
® connector
BP892cLM3, BP892cLM3-TH – Terminated for Sennheiser
® wireless systems using locking 3.5 mm connector
BP892cT4, BP892cT4-TH – Terminated for Shure
® wireless systems using TA4F-type connector
BP892cT5, BP892cT5-TH – Terminated for Lectrosonics
® wireless systems using TA5F-type connector
BP892c, BP892c-TH – Unterminated
Audio-Technica® is a registered trademark of Audio-Technica. Other product and company names mentioned herein may
be trademarks and/or service marks of their respective owners.
1
23
4
1
4
3
2
Tip
Ring
Sleeve
1
5
4
32
1
2
3
Pin 1 Pin 2 Pin 3 Pin 4
Function Ground / Shield Instrument Mic Audio Blas + In
Wire Colour Green Jumper to Pin 1 Copper Colour Red
Pin 1 Pin 2 Pin 3 Pin 4
Function Ground / Shield Blas + In Mic Audio Source Load
Wire Colour Green Red Copper Colour Jumper to Pin 1
Pin 1 Pin 2 Pin 3 Pin 4 Pin 5
Function Ground / Shield Blas + In Mic Audio Source Load Line In
Wire Colour Green Red Copper Colour Jumper to Pin 1 Open
Pin 1 Pin 2 Pin 3 Shell / Case
Function N/C N/C Blas + In, Mic Audio Ground / Shield
Wire Colour Open Open Red Green
Sleeve Ring Tip
Function Ground / Shield Mic Audio Blas + In
Wire Colour Green Copper Colour Red
FORM No. ATGC-L0165-10-E
Machida • Tokyo • Japan
Specyfikacje produktu
| Marka: | Audio-Technica |
| Kategoria: | słuchawka |
| Model: | BP892 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Audio-Technica BP892, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje słuchawka Audio-Technica
24 Lipca 2024
24 Lipca 2024
29 Maja 2024
28 Maja 2024
27 Maja 2024
25 Maja 2024
22 Maja 2024
12 Maja 2024
12 Maja 2024
11 Maja 2024
Instrukcje słuchawka
- LD Systems
- Bose
- Lexibook
- Krüger&Matz
- Aiwa
- Focal
- Galaxy Audio
- Speed-Link
- Klein Tools
- Fresh 'n Rebel
- Boompods
- Edifier
- HP
- Nedis
- Monster
Najnowsze instrukcje dla słuchawka
23 Października 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
21 Września 2024
21 Września 2024
21 Września 2024
21 Września 2024
21 Września 2024