Instrukcja obsługi Audio-Technica ES933/ML
Audio-Technica
mikrofon
ES933/ML
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Audio-Technica ES933/ML (2 stron) w kategorii mikrofon. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 9 użytkowników na średnio 4.9 gwiazdek
Strona 1/2
MicroLine® CONDENSER
HANGING MICROPHONE
- Designed for quality sound
reinforcement, professional
recording, television and other
demanding sound pickup
applications.
- Superior off-axis rejection for
maximum gain before feedback.
- Furnishing with a vinyl-coated steel
hanger that allows to be adjusted for
correct positioning.
- Accepts interchangeable elements
to permit angle of acceptance from
90° to 120°.
- Snap-on foam windscreen effectively
reduces noise from wind or
ventilation air currents.
- Connected power module can be
powered from any external 11V to
52V phantom power supply with an
XLRM-type connector.
- Enclosed in a rugged housing with a
low-reectance black nish. And also
available with white housing, cable
and hanger as the ES993W/ML.
The ES933/ML shall have a permanently-attached 15.2m miniature low-
noise cable, and require 11V to 52V DC phantom power for operation.
A uniform 90° angle of acceptance provides well-balanced audio
pickup. The microphone should be located forward of the front-most
source, above the rear-most source, and "aimed" between them (Fig.1).
Increasing the height of the mic above the sources will tend to equalize
sound levels between them, but may also increase from the mic to the
rear-most pickup should be no more than twice the distance to the front
source, to maintain front-to-rear balance (Fig.1).
Width of pickup is approximately 1.5 times the distance to the closest
performer. If additional mics are needed for wide sources, they should
be positioned apart laterally at least 1.5 times the distance to front
source, to avoid phase cancellation (Fig.2).
Output is low impedance balanced. The output connector mates with
XLRF-type cable connectors. The balanced signal appears across Pins
2 and 3, while the ground (shield) connection is Pin 1. Output is phased
so that positive acoustic pressure produces positive voltage at Pin 2, in
accordance with industry convention.
At integral 80 Hz high-pass filter provides easy switching from a flat
frequency response to a low-end roll-off. The roll-off position reduces
the pickup of low-frequency ambient noise (such as trafc, air-handling
systems, etc.), room reverberation and mechanically coupled vibrations.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 43°C for extended periods. Extremely high
humidity should also be avoided.
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
0°
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
Optional Accessories:
AT8506 four-channel 48V phantom power
supply (AC powered).
AT8801/EU single-channel 48V phantom
power supply (AC powered).
Polar Pattern
Frequency Response
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
Frequency in Hertz
LEGEND 12” or more on axis
Roll-off
Response in dB
FORM No. ATGC-L0057-06-E
Machida • Tokyo • Japan
SPECIFICATIONS
ELEMENT Fixed-charge back plate
permanently polarized condenser
POLAR PATTERN MicroLine ®
FREQUENCY RESPONSE 30-20,000 Hz
LOW-FREQUENCY ROLL-OFF 80 Hz, 12 dB/octave
OPEN CIRCUIT SENSITIVITY -35 dB (17.7 mV) re 1V at 1 Pa
IMPEDANCE 250 Ω (1000 Ω without power module)
MAXIMUM INPUT SOUND LEVEL 133 dB SPL, 1 kHz at 1% T.H.D.
DYNAMIC RANGE (typical) 107 dB, 1 kHz at Max SPL
SIGNAL-TO-NOISE RATIO 68 dB, 1 kHz at 1Pa
SWITCHES Flat response, low-roll-off
PHANTOM POWER REQUIREMENTS 11-52V DC, 4 mA typical
WEIGHT Microphone
Power Module
14 g
56 g
DIMENSIONS Microphone
Power Module
143.3 mm - long,
8.0 mm - head diameter
98.0 mm - long,
18.9 mm - diameter
OUTPUT CONNECTOR Integral 3-pin XLRM-type
CABLE 15.2m - long, 3.2 mm - diameter
ACCESSORIES FURNISHED AT8138 foam windscreen
AT8452 steel hanger
OPTIONAL INTERCHANGEABLE
ELEMENTS
ESE-C cardioid (120°)
ESE-H hypercardioid (100°)
1.5 TIMES
DISTANCE "X"
MIC A MIC B
90° 90°
90°
ANGLE OF
ACCEPTANCE
DISTANCE "X"
LESS THAN 2 TIMES "X"
Fig.2Fig.1
Specyfikacje produktu
| Marka: | Audio-Technica |
| Kategoria: | mikrofon |
| Model: | ES933/ML |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Audio-Technica ES933/ML, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje mikrofon Audio-Technica
1 Marca 2025
13 Stycznia 2025
6 Grudnia 2024
6 Grudnia 2024
6 Grudnia 2024
6 Grudnia 2024
6 Grudnia 2024
6 Grudnia 2024
6 Grudnia 2024
6 Grudnia 2024
Instrukcje mikrofon
- TC Helicon
- Hama
- Artsound
- Neat
- Microtech Gefell
- Elgato
- Yamaha
- Bogen
- RCF
- Apart
- Tascam
- Zoom
- ITek
- Aston Microphones
- Singing Machine
Najnowsze instrukcje dla mikrofon
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
8 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025