Instrukcja obsługi Axxess AX-MLOC-HD1
Axxess
Niesklasyfikowane
AX-MLOC-HD1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Axxess AX-MLOC-HD1 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 31 osób i została oceniona przez 16 użytkowników na średnio 5.0 gwiazdek
Strona 1/2
®
Installation Instructions for AX-MLOC-HD1
REV. 4/6/17
• axxessinterface.com
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
Axxess Integrate
®
A two channel adjustable L.O.C. (Line Output Converter) with a built in amplifier
remote generator, the AX-MLOC-HD1 is designed to convert (2) channels of speaker
level audio into (2) channels of line level audio that can be used by an aftermarket
amplifier. This device will also detect the presence of an audio signal and then
generate a +12V output that can be used to turn-on an aftermarket amplifier
.
Features and specifications:
The AX-MLOC-HD1 is able to handle 80
watts per channel continuous input without overheating. The input circuitry is
designed to correct the crossover distortion commonly found on standard L.O.C.’s,
while providing a high to low level step down of 6:1. Output audio level is infinitely
adjustable using the onboard, high quality potentiometers. The remote output, or
amplifier trigger, is rated at 500mA (+12V), and will easily handle an outboard
relay if additional current is needed. The remote output will trigger instantaneously
when the LOC detects DC voltage on the white, left + audio input wire above 5V, or
a very low audio signal. It will shut off 60 seconds after no signal is detected
.
Installation:
The AX-MLOC-HD1 should be installed on the radios speaker
output wires. These connectors are found behind the radio in the bike’s fairing,
before the speaker pods. We have provided speaker harnesses that can be used to
run the output signal to the speaker without destroying the wiring of the speaker
pod. Please refer to the wiring diagram for the input and output connection details.
Wire color and function: The audio and power input wire colors are an
EIA standard color for car stereo applications as follows:
Yellow battery +12v input
Black ground input
Blue remote +12v output
(the
above power wires can be
connected directly to the
amplifier being added)
White left front (+) input
White/Black left front (-) input
Gray right front (+) input
Gray/Black right front (-) input
Brown
reference ground (-)
(reference ground
optional if noise is
present)
Note: Be sure that all audio input connections are polarized or in phase with each
other. Failure to do this will result in poor bass response and low quality audio.
Adjusting the AX-MLOC-HD1 for maximum performance: After completing all of the
necessary connections, turn the adjustment pots all of the way down by rotating them
completely counter-clockwise. Now, turn the stereo system on and adjust the main
volume control on the stereo to approximately ¾ maximum volume. Select one of the
adjustment pots and turn it slowly clockwise until you notice audio distortion, and then
stop. Turn the remaining pot to the same position as the previously adjusted pot. The
audio set-up of the is now complete and ready to be enjoyed.AX-MLOC-HD1
Loose black connectors:
White left front (+) output
from amplifier
White/Black left front (-) output
from amplifier
Gray right front (+) output
from amplifier
Gray/Black right front (-) output
from amplifier
K PNOWLEDGE IS OWER
Enhance your installation and fabrication skills by
enrolling in the most cognized and spected re re
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for mo information and take steps re
toward a better tomorrow.
Metra recommends MECP
certified technicians
CAUTION!
All accessories, switches, climate controls panels, and especially air bag
indicator lights must be connected before cycling the ignition. Also, do not remove the
factory radio with the key in the on position, or while the vehicle is running.
Specyfikacje produktu
| Marka: | Axxess |
| Kategoria: | Niesklasyfikowane |
| Model: | AX-MLOC-HD1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Axxess AX-MLOC-HD1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Axxess
9 Października 2024
Instrukcje Niesklasyfikowane
- Sylvania
- Pigtronix
- Nilfisk
- XYZprinting
- Osram
- PCE
- Davey
- OneConcept
- Varta
- Nabo
- Klauke
- ICOM
- Vizio
- Wamsler
- Euro Cuisine
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025