Instrukcja obsługi Axxess LC-BMRC-01
Axxess
nieskategoryzowany
LC-BMRC-01
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Axxess LC-BMRC-01 (8 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 5.0 gwiazdek
Strona 1/8
Installation instructions for part LC-BMRC-01
REV. 5/13/2016 INSTLC-BMRC-01
axxessinterfaces.com • metraonline.com © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
Axxess Integrate
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
• Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, and V.S.S)
• Retains warning chimes
• For non-amplified models, or when bypassing a factory amplifier
• Retains balance and fade
• Micro “B” USB updatable
FEATURES
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
TOOLS REQUIRED
LC-BMRC-01
BMW / Mini Chime Retention
2006-2015
APPLICATIONS
• LC-BMRC-01 interface • LC-BMRC-01 harness
• Fuse holder with 96” length of wire
INTERFACE COMPONENTS
BMW
1 Series (without amp) 2008-2013
3 Series (without amp) 2006-2013
M3 (without amp) 2007-2013
MINI
Cooper (without amp) 2007-2015
Connections to be made 2 ...................................................
Installing the LC-BMRC-01 3 ...............................................
Initializing the LC-BMRC-01 3 .............................................
TABLE OF CONTENTS
LC-BMRC-01
From the LC-BMRC-01 harness to the aftermarket radio:
• Connect the wire to the ground wire.Black
• Connect the Yellow wire to the fuse holder with 96” length of wire:
• Remove the fuse from the fuse holder.
• Connect the 6” long wire side of the fuse holder to the vehicles battery.
• Connect the 96” long wire side of the fuse holder to the Yellow wire.
• Connect the wire to the accessory wire.Red
• Connect the wire to the power antenna wire.Blue
• If the aftermarket radio has an illumination wire, connect the wire to it.Orange
• Connect the wire to the right front positive speaker output.Gray
• Connect the wire to the right front negative speaker output.Gray/Black
• Connect the wire to the left front positive speaker output.White
• Connect the wire to the left front negative speaker output.White/Black
• Connect the wire to the left rear positive speaker output.Green
• Connect the wire to the left rear negative speaker output.Green/Black
• Connect the wire to the right rear positive speaker output.Purple
• Connect the wire to the right rear negative speaker output.Purple/Black
The following (3) wires are only for multimedia/navigation radios that require these
wires.
• Connect the wire to the VSS/speed sense wire.Blue/Pink
• Connect the wire to the reverse wire.Green/Purple
• Connect the wire to the parking brake wire.Light Green
12-pin pre-wired ASWC-1 harness:
• This harness is to be used along with the optional ASWC-1 (not included) to
retain steering wheel audio controls. If the ASWC-1 is not being used, disregard
this harness. If it will be used, please refer to the ASWC-1 instructions for radio
connections and programming.
Note: Disregard the harness that comes with the ASWC-1.
Connections to be made
LC-BMRC-01
Installing the LC-BMRC-01
With the key in the off position:
• Connect the LC-BMRC-01 harness into the interface, and then to the vehicle.
• Re-insert the fuse back into the fuse holder.
Attention! If the interface loses power for any reason, the following steps will need
to be performed again. Also, if installing an ASWC-1 connect it after you initialize
and test the interface/radio, with the key in the off position.
• Turn the key (or push-to-start button) to the ignition position and wait until the
radio comes on.
Note: If the radio does not come on within 60 seconds, turn the key to the
off position, disconnect the interface, check all connections, reconnect the
interface, and then try again.
• Turn the key to the off position, and then to the accessory position. Test all
functions of the installation for proper operation, before reassembling the dash.
Initializing the LC-BMRC-01
Specyfikacje produktu
| Marka: | Axxess |
| Kategoria: | nieskategoryzowany |
| Model: | LC-BMRC-01 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Axxess LC-BMRC-01, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje nieskategoryzowany Axxess
10 Września 2024
10 Września 2024
10 Września 2024
10 Września 2024
10 Września 2024
10 Września 2024
10 Września 2024
10 Września 2024
10 Września 2024
10 Września 2024
Instrukcje nieskategoryzowany
- nieskategoryzowany Lumantek
- nieskategoryzowany Gossen Metrawatt
- nieskategoryzowany OBH Nordica
- nieskategoryzowany Medela
- nieskategoryzowany Vincent
- nieskategoryzowany Kenwood
- nieskategoryzowany Intex
- nieskategoryzowany BeamZ
- nieskategoryzowany Bavaria
- nieskategoryzowany Tronic
- nieskategoryzowany SunBriteTV
- nieskategoryzowany Thetford
- nieskategoryzowany Pro-Ject
- nieskategoryzowany Vicoustic
- nieskategoryzowany Midland
Najnowsze instrukcje dla nieskategoryzowany
28 Października 2024
28 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024